AXA010A0G93-SRZ Lineage Power, AXA010A0G93-SRZ Datasheet - Page 18
![DC/DC Converters & Regulators 2.5Vout 10A SMT 10-14Vin](/photos/33/22/332211/superlynxsmte_sml.jpg)
AXA010A0G93-SRZ
Manufacturer Part Number
AXA010A0G93-SRZ
Description
DC/DC Converters & Regulators 2.5Vout 10A SMT 10-14Vin
Manufacturer
Lineage Power
Series
AXA010r
Datasheet
1.108970013.pdf
(20 pages)
Specifications of AXA010A0G93-SRZ
Product
Non-Isolated / POL
Output Power
25 W
Input Voltage Range
10 V to 14 V
Number Of Outputs
1
Output Voltage (channel 1)
2.5 V
Output Current (channel 1)
10 A
Package / Case Size
SMD
Output Type
Non-Isolated
Output Voltage
2.5 V
Package / Case
SMD
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
CC109102860
Data Sheet
March 14, 2006
Surface Mount Information
Pick and Place
The Austin Lynx
frame construction and are designed for a fully
automated assembly process. The modules are fitted
with a label designed to provide a large surface area
for pick and place operations. The label meets all the
requirements for surface mount processing, as well as
safety standards, and is able to withstand reflow
temperatures of up to 300
product information such as product code, serial
number and the location of manufacture.
Figure 33. Pick and Place Location.
Nozzle Recommendations
The module weight has been kept to a minimum by
using open frame construction. Even so, these
modules have a relatively large mass when compared
to conventional SMT components. Variables such as
nozzle size, tip style, vacuum pressure and placement
speed should be considered to optimize this process.
The minimum recommended nozzle diameter for
reliable operation is 6mm. The maximum nozzle outer
diameter, which will safely fit within the allowable
component spacing, is 9 mm.
Oblong or oval nozzles up to 11 x 9 mm may also be
used within the space available.
Tin Lead Soldering
The Austin Lynx
free modules and can be soldered either in a lead-free
solder process or in a conventional Tin/Lead (Sn/Pb)
process. It is recommended that the customer review
data sheets in order to customize the solder reflow
profile for each application board assembly. The
following instructions must be observed when
soldering these units. Failure to observe these
LINEAGE
POWER
TM
TM
12 V SMT modules use an open
12 V SMT power modules are lead
o
C. The label also carries
10 – 14Vdc input; 1.2Vdc to 5.5Vdc Output; 10A output current
Austin Lynx
TM
instructions may result in the failure of or cause
damage to the modules, and can adversely affect
long-term reliability.
In a conventional Tin/Lead (Sn/Pb) solder process
peak reflow temperatures are limited to less than
235
wets the land, and subsequently wicks the device
connection. Sufficient time must be allowed to fuse
the plating on the connection to ensure a reliable
solder joint. There are several types of SMT reflow
technologies currently used in the industry. These
surface mount power modules can be reliably
soldered using natural forced convection, IR (radiant
infrared), or a combination of convection/IR. For
reliable soldering the solder reflow profile should be
established by accurately measuring the modules CP
connector temperatures.
Figure 34. Reflow Profile for Tin/Lead (Sn/Pb)
process.
Figure 35. Time Limit Curve Above 205
Tin/Lead (Sn/Pb) process.
12 V SMT Non-isolated Power Modules:
o
300
200
240
235
230
225
220
205
200
250
100
215
210
150
C. Typically, the eutectic solder melts at 183
50
0
0
10
Heat zo ne
max 4
P reheat zo ne
max 4
P eak Temp 235
20
REFLOW TIME (S)
o
Cs
o
So ak zo ne
30-240s
Cs
-1
-1
30
o
C
40
T
205
lim
o
above
C
o
Co o ling
zo ne
1 -4
C for
50
o
Cs
-1
o
18
60
C,