LAN9512-JZX SMSC, LAN9512-JZX Datasheet - Page 45

• Manufacturer Part Number: LAN9512-JZX
• Description: IC USB 2.0 ETHER CTRLR 64QFN
• Manufacturer: SMSC

Specifications of LAN9512-JZX

• Controller Type: Ethernet Controller
• Interface: IEEE 802.3
• Voltage - Supply: 3 V ~ 3.6 V
• Current - Supply: 231mA
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 64-QFN
• Product: Ethernet Controllers
• Standard Supported: 802.3, 802.3u
• Data Rate: 1.5 Mbps to 480 Mbps
• Supply Voltage (max): 3.6 V
• Supply Voltage (min): 3 V
• Supply Current (max): 231 mA
• Maximum Operating Temperature: + 70 C
• Ethernet Connection Type: 10/100 Base-T
• Maximum Power Dissipation: 763 mW
• Minimum Operating Temperature: 0 C
• Mounting Style: SMD/SMT
• For Use With: 638-1093 - EVALUATION BOARD FOR LAN9512
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 638-1086

USB 2.0 Hub and 10/100 Ethernet Controller
Datasheet
SMSC LAN9512/LAN9512i
4.6
Crystal Cut
Crystal Oscillation Mode
Crystal Calibration Mode
Frequency
Frequency Tolerance @ 25
Frequency Stability Over Temp
Frequency Deviation Over Time
Total Allowable PPM Budget
Shunt Capacitance
Load Capacitance
Drive Level
Equivalent Series Resistance
Operating Temperature Range
LAN9512/LAN9512i XI Pin
Capacitance
LAN9512/LAN9512i XO Pin
Capacitance
PARAMETER
LAN9512/LAN9512i can accept either a 25MHz crystal (preferred) or a 25MHz single-ended clock
oscillator (+/- 50ppm) input. If the single-ended clock oscillator method is implemented, XO should be
left unconnected and XI should be driven with a nominal 0-3.3V clock signal. The input clock duty cycle
is 40% minimum, 50% typical and 60% maximum.
It is recommended that a crystal utilizing matching parallel load capacitors be used for the crystal
input/output signals (XI/XO). See
Note 4.13 The maximum allowable values for Frequency Tolerance and Frequency Stability are
Note 4.14 Frequency Deviation Over Time is also referred to as Aging.
Note 4.15 The total deviation for the Transmitter Clock Frequency is specified by IEEE 802.3u as
Note 4.16 0
Note 4.17 +70
Note 4.18 This number includes the pad, the bond wire and the lead frame. PCB capacitance is not
Clock Circuit
application dependant. Since any particular application must meet the IEEE +/-50 PPM
Total PPM Budget, the combination of these two values must be approximately +/-45 PPM
(allowing for aging).
+/- 50 PPM.
included in this value. The XO/XI pin and PCB capacitance values are required to
accurately calculate the value of the two external load capacitors. These two external load
capacitors determine the accuracy of the 25.000 MHz frequency.
o
C for commercial version, -40
o
C
o
Table 4.7 LAN9512/LAN9512i Crystal Specifications
C for commercial version, +85
SYMBOL
F
F
F
F
P
C
temp
C
R
fund
age
tol
W
O
L
1
Table 4.7
DATASHEET
Note 4.16
MIN
300
Parallel Resonant Mode
-
-
-
-
-
-
-
-
-
-
45
for the recommended crystal specifications.
o
Fundamental Mode
C for industrial version.
o
C for industrial version.
AT, typ
+/-3 to 5
25.000
20 typ
NOM
7 typ
3 typ
3 typ
-
-
-
-
-
-
Note 4.17
+/-50
+/-50
+/-50
MAX
50
-
-
-
-
-
-
-
UNITS
PPM
PPM
PPM
PPM
Ohm
MHz
uW
Revision 1.0 (11-24-09)
pF
pF
o
pF
pF
C
Note 4.13
Note 4.13
Note 4.14
Note 4.15
Note 4.18
Note 4.18
NOTES