PSA1554-605Chassis-R PHIHONG USA, PSA1554-605Chassis-R Datasheet - Page 2

• Manufacturer Part Number: PSA1554-605Chassis-R
• Description: Linear & Switching Power Supplies 19in Rack at 1U High For PSM500 PS
• Manufacturer: PHIHONG USA
• Series: PSAr

Specifications of PSA1554-605Chassis-R

• Product: Mounting Hardware
• Commercial/medical: Commercial
• Output Power Rating: 1512 W
• Input Voltage: 90 VAC to 264 VAC
• Number Of Outputs: 3
• Output Voltage (channel 1): 50 V, 56 V
• Output Current (channel 1): 10 A, 9 A, 30 A, 27 A
• Output Voltage (channel 2): 50 V, 56 V
• Output Current (channel 2): 10 A, 9 A, 30 A, 27 A
• Output Voltage (channel 3): 50 V, 56 V
• Output Current (channel 3): 10 A, 9 A, 30 A, 27 A
• Mounting Style: Chassis
• Output Type: Triple
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

INPUT:
AC Input Voltage Range
90 to 264VAC
AC Input Current
3 x 6A (RMS) maximum for 115VAC
3 x 3A (RMS) maximum for 230VAC
AC Input Line Fuse
10A/ 250V
(located internally in module)
Leakage Current (per module)
3.5mA maximum @ 254VAC 60Hz
AC Input Frequency (per module)
47-63Hz
AC Inrush Current (per module)
30A (RMS) maximum for 115VAC
60A (RMS) maximum for 230VAC
OUTPUT:
Power
500 –15000W continuous
Efficiency per Module
80% (typical) at maximum load, and 115VAC/230VAC
Hold-up Time
10mS min. 120VAC and maximum load
Over Voltage Protection (per module)
OV set at 57~60V – latching
Over Current Protection
Protection against short circuit. Isc max set to 120%-140%
full load current per module. Within the rack, each module
is load protected by PTC Resettable Fuses. Output may be
shorted permanently without damage.
ENVIRONMENTAL:
Temperature
Operation
Non-operation
Humidity
Operation
Isolation Test (per module)
Primary to Secondary: 4242V DC
Primary to Field Ground: 2121V DC
Output to Field Ground: 2121 V DC
PSA1554-605 Characteristics
0 to +40°C
-30 to +70°C
8 to 90%
+50V
+50V
+50V Return
Current Share
Not Used
Not Used
Standby 12V
EMC
EN55022 conducted Class B; radiated Class A
(Measured using 3 x PSM500-XXX, in PSA1554-611)
Immunity (per module)
ESD:
RS:
EFT:
Surge:
CS:
Voltage Dips
Harmonic:
FEATURE:
Front Panel LED
DC Good, Fault condition per module
Rear Panel LED
Red LED illuminates when a fault such as SC or Overload
has cause the internal PTC to go high impedance.
Enable/Disable (main 50V/56V)
Non latching – remote on/off pin
Thermal Shutdown (per module)
Latching
Fan Fail (per module)
Latching
Load Sharing
10% at full load
Isolated Diode
Internal O-ring Diode Located on main (-) output section
Output Connector
14 pin Molex p/n 39301140
14 pin Molex p/n39012145 (mating x 4 per rack), pin p/n
39000077 or equivalent
*Fault: A fault low signal at pin 13 of output connector A,B, or
C represents a fault to Module 1,2 or 3. A fault low signal at
pin 13 of output connector D represents a global fault to rack.
**Common Ground, standby and Fault
Signal
Reference
EN61000-4-2. Level 3
EN61000-4-3. Level 3
EN61000-4-4. Level 2
EN61000-4-5. Level 3
EN61000-4-6. Level 3
EN61000-4-11
EN61000-3-2
Pin
1
2
3
4
5
6
7
WWW.PHIHONG.COM
+50V
+50V Return
+50V Return
Not Used
Not Use
*Fault
**Common GND
Signal
Reference
Pin
10
11
12
13
14
8
9