MPU150-4350 POWER ONE, MPU150-4350 Datasheet - Page 3

• Manufacturer Part Number: MPU150-4350
• Description: Linear & Switching Power Supplies 150W +3.3,+5,12,12V QUAD OUT
• Manufacturer: POWER ONE
• Type: Commercialr

Specifications of MPU150-4350

• Product: Switching
• Commercial/medical: Commercial
• Output Power Rating: 99 W
• Input Voltage: 85 VAC to 264 VAC
• Number Of Outputs: 4
• Output Voltage (channel 1): 3.3 V
• Output Current (channel 1): 30 A
• Output Voltage (channel 2): 5 V
• Output Current (channel 2): 15 A
• Output Voltage (channel 3): - 12 V
• Output Current (channel 3): 4 A
• Mounting Style: Chassis
• Dimensions: 8 in L x 4.2 in W x 1.5 in H
• Brand/series: MPU150 Series
• Configuration: Open-Frame
• Current, Input: 3 A (RMS) (Max.)
• Current, Leakage: 22 mA (Max.) @ Dual Output MPU150, 264 VAC
• Hold Time: 17.5 ms (Min.)
• Mounting Type: Panel
• Operation: Switching
• Output: +3.3 VDC @ 30 A, +5 VDC @ 15 A, 12 VDC @ 3 A, 12 VDC @ 3 A
• Power, Output: 150 W
• Power, Rating: 150 W (Nom.)
• Primary Type: AC-DC
• Special Features: PFC, Remote Sense
• Temperature, Operating: 0 to +50 °C @ 100 % Load
• Voltage, Input: 85 to 264 VAC
• Voltage, Output: +3.3, +5, 12, 12 VDC
• Output Current (max): 30/15/3A
• Output Voltage: 3.3/5/12V
• Output Power (max): 150W
• Input Frequency: 47 to 63Hz
• Efficiency: 75%
• Screening Level: Commercial
• Product Length (mm): 203.2mm
• Product Height (mm): 38.1mm
• Product Depth (mm): 106.7mm
• Operating Temperature Min Deg. C: 0C
• Operating Temperature Max Deg. C: 50C
• Pin Count: 15
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

MDU150 Input Specifications
PARAMETER
Input Voltage - DC
Brown Out Protection
Hold-up Time
Input Current
Input Protection
Operating Frequency
Inrush Current
Output Specifications
PARAMETER
Efficiency
Minimum Load, V1
Minimum Load, V3
Ripple and Noise
Output Power
Overshoot / Undershoot
Regulation
Transient Response
Turn-on Delay
Turn-on Rise Time
NOTES: 1) This product is not rated for convection applications.
Interface Signals and Internal Protection
PARAMETER
Overvoltage Protection
Overload Protection
Overtemperature Protection
Output Good Signal,
Low to High Transition
Input Power Fail Warning
Current Share
Remote Sense
Inhibit
CONDITIONS/DESCRIPTION
Continuous input range.
Lowest DC input voltage that regulation is maintained with full rated loads.
At 150 watts, over DC input range.
36 VDC at full rated load.
Non-user serviceable internally located AC input line fuse.
Switching frequency of main output transformer.
Switching frequency of secondary transformer.
Consult factory.
CONDITIONS/DESCRIPTION
Full Rated Load, 110 VAC. Varies with distribution of loads among outputs.
Minimum load required to maintain regulation on,
V2 at maximum load.
Minimum load required on single output models.
Minimum load required to maintain regulation on
V4 at maximum load.
Full load, 20 MHz bandwidth.
With 300 LFM forced air cooling. (Note 1)
Output voltage overshoot/undershoot at turn-on.
Varies by output. Total regulation includes: line changes over the specified.
input range, changes in load starting at 20% load and changing to 100% load.
Recovery time, to within 1% of initial set point due to a 50-100% load change,
5% max. deviation.
Time required for initial output voltage stabilization.
Time required for output voltage to rise from 10% to 90%.
CONDITIONS/DESCRIPTION
Latch style overvoltage protection. Available on
V1, V2, all models, and V3 on all models except
MPU150-3300.
Fully protected against output overload and short circuit. Automatic recovery upon removal of overload condition.
System shutdown due to excessive internal temperature, automatic reset.
TTL compatible signal available for V1. Pull-up resistor is 10k . Signal
is high when output is above the specified limits. Signal shall remain low
for 20 milliseconds following loss of Output Good.
TTL compatible logic signal. Time before regulation dropout due to loss of input
power. May be used as independent PSOK signal in redundant applications.
Accuracy of shared current with up to 6 parallel units. Single wire current share
on V1 and V2 with return via -Sense return.
Available on V1 and V2. Total voltage compensation for cable losses with
respect to the main output.
Output voltage is inhibited by application of an external high (5V) signal.
Page 3 of 6
MPU150-4350G 3.3V output, V1
MPU150/MDU150 Series Data Sheet
Single output models V1
Triple output models V1
Triple output models V3
Quad output models V1
Quad output models V3
MPU150-S259 12V
MPU150-S262 24V
MPU150-S261 48V
MPU150-S259 V1
MPU150-S262 V1
MPU150-S261 V1
5V output, V1, V2
2.5V output, V1
3.3V output, V1
3.3V output, V2
12V output, V2
12V output, V3
3.3V
5V
17.0
32.0
58.0
3.16
4.75
10.5
21.5
43.0
MIN
MIN
MIN
0.3
3.0
4.1
3.8
6.0
4.3
65
36
34
20
14
14
4
3
0
0
0
5
See Model Selection Charts
See Model Selection Charts
NOM
NOM
NOM
100
150
500
70
75
50
10
3
2
3.25
4.65
4.65
20.5
38.0
62.7
3.25
4.90
11.9
23.5
47.0
MAX
MAX
MAX
500
6.4
4.2
6.4
75
16
19
5
A
Watts
UNITS
UNITS
UNITS
VDC
VDC
kHz
mV
ms
RMS
ms
ms
%
%
µs
%
A
A
V
V
s