MAX682ESA Maxim Integrated Products, MAX682ESA Datasheet - Page 7

no-image

MAX682ESA

Manufacturer Part Number
MAX682ESA
Description
Charge Pumps 3.3VIn to Reg 5Vout Charge Pump
Manufacturer
Maxim Integrated Products
Datasheet

Specifications of MAX682ESA

Function
Step Up
Output Voltage
5.05 V
Output Current
250 mA
Maximum Operating Temperature
+ 85 C
Package / Case
SOIC-8 Narrow
Minimum Operating Temperature
- 40 C
Mounting Style
SMD/SMT

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
MAX682ESA
Manufacturer:
MAXIM
Quantity:
127
Part Number:
MAX682ESA
Manufacturer:
MAXIM/美信
Quantity:
20 000
Part Number:
MAX682ESA+
Manufacturer:
Maxim
Quantity:
500
Part Number:
MAX682ESA+
Manufacturer:
MAXIM/美信
Quantity:
20 000
Part Number:
MAX682ESA+T
Manufacturer:
MAXIM
Quantity:
481
Part Number:
MAX682ESA+T
Manufacturer:
MAXIM/美信
Quantity:
20 000
Part Number:
MAX682ESA-T
Manufacturer:
MAXIM/美信
Quantity:
20 000
Part Number:
MAX682ESA-T
Quantity:
2 000
Company:
Part Number:
MAX682ESA-T
Quantity:
389
output noise contains well-defined frequency compo-
nents, and the circuit requires much smaller external
capacitors for a given output ripple. However, constant-
frequency mode, due to higher operating current, is
less efficient at light loads than skip mode. Note: For
input voltages above 3.6V, the devices must operate in
constant-frequency mode. Table 1 summarizes the
tradeoffs between the two operating modes.
The SHDN pin on the MAX682/MAX683/MAX684 per-
forms a dual function: it shuts down the device and
determines the oscillator frequency. The SHDN input
looks like a diode to ground and should be driven
through a resistor.
Driving SHDN low places the device in shutdown
mode. This disables all switches, the oscillator, and
control logic. The device typically draws 0.1µA (5µA
Figure 4. Constant-Frequency-Mode Regulation
Table 1. Tradeoffs Between Operating
Modes
Best Light-Load
Efficiency
Smallest External
Component Size
Output Ripple
Amplitude and
Frequency
Load Regulation
C
IN
IN
FEATURE
N-CHANNEL
S1
Frequency Selection and Shutdown
amplitude, variable
_______________________________________________________________________________________
C
Relatively large
(SKIP = LOW)
X
SKIP MODE
Very Good
frequency
S2
OSC
3.3V-Input to Regulated 5V-Output
FREQUENCY MODE
amplitude, constant
Relatively small
(SKIP = HIGH)
CONSTANT-
frequency
Good
C
OUT
OUT
max) of supply current in this mode and the output pre-
sents a 50kΩ impedance to ground. The device exits
shutdown once SHDN is forward biased (minimum of
1µA of current). The typical no-load shutdown exit time
is 50µs.
When SHDN is pulled high through an external resistor
to V
charge-pump frequency. To select the frequency, cal-
culate the external resistor value, R
lowing formula:
where R
frequency in the 50kHz to 2MHz range. This frequency
range corresponds to SHDN input currents between
1µA and 50µA. Proper operation of the oscillator is not
guaranteed beyond these limits. Currents lower than
1µA may shut down the device. The forward-biased
diode voltage from the SHDN input to GND has a tem-
perature coefficient of -2mV/°C.
The MAX682/MAX683/MAX684 have an undervoltage-
lockout feature that deactivates the devices when the
input voltage falls below 2.25V. Regulation at low input
voltages cannot be maintained. This safety feature
ensures that the device shuts down before the output
voltage falls out of regulation by a considerable amount
(typically 10% with no load). Once deactivated, hys-
teresis holds the device in shutdown until the input volt-
age rises 100mV above the lockout threshold.
The MAX682/MAX683/MAX684 require only three exter-
nal capacitors (Figure 5). Their values are closely linked
to the output current capacity, oscillator frequency, out-
put noise content, and mode of operation.
Generally, the transfer capacitor (C
est, and the input capacitor (C
C
smaller C
be anywhere from 5-times to 50-times larger than C
depending on the mode of operation and ripple toler-
ance. In continuous switching mode, smaller output rip-
ple allows smaller C
required to maintain low output ripple. Tables 2 and 3
show capacitor values recommended for lowest sup-
ply-current operation (skip mode) and smallest size oper-
ation (constant-frequency mode), respectively.
X
. Higher switching frequencies allow the use of
IN
, the bias current into SHDN determines the
EXT
X
R
EXT
and C
is in kΩ and f
= 45000 (V
Applications Information
IN
OUT
. The output capacitor (C
Charge Pumps
. In skip mode, a larger C
Undervoltage Lockout
IN
OSC
- 0.69V) / f
Capacitor Selection
IN
is in kHz. Program the
) is twice as large as
X
EXT
) will be the small-
OSC
, using the fol-
OUT
OUT
) can
X
is
7
,

Related parts for MAX682ESA