MAX881REUB-T Maxim Integrated Products, MAX881REUB-T Datasheet - Page 6

• Manufacturer Part Number: MAX881REUB-T
• Description: Charge Pumps Bias Supply w/Power OK for GaAsFET PA
• Manufacturer: Maxim Integrated Products

Specifications of MAX881REUB-T

• Function: Inverting
• Output Voltage: - 4.9 V to - 0.5 V
• Output Current: 4 mA
• Maximum Operating Temperature: + 85 C
• Package / Case: uMAX-10
• Minimum Operating Temperature: - 40 C
• Mounting Style: SMD/SMT

The MAX881R, a low-noise, inverting, regulated charge-
pump power supply, is designed for biasing GaAsFET
devices such as power-amplifier modules in cellular
handsets.
The applied input voltage (V
voltage at NEGOUT by a capacitive charge pump. This
voltage is regulated by an internal linear regulator at
OUT (Figure 1). With FB connected to GND, V
regulated at -2V. Alternatively, use a voltage-divider at
FB to adjust the output voltage between -0.5V and -(V
- 0.6V) (see the section Setting the Output Voltage).
The internal linear regulator reduces the ripple noise
induced by the charge-pump inverter to 1mVp-p at
OUT (circuit of Figure 3b). In addition, the excellent AC
rejection of the linear regulator attenuates noise from
the incoming supply.
The MAX881R has an active-low, open-drain, power-OK
(POK) output. This output goes low when OUT reaches
92.5% of the regulated output voltage. POK can be
used to drive the gate of a P-MOSFET that switches
power to the GaAsFET power amplifier (Figure 2), there-
by ensuring that the power amplifier is not powered
before the required negative bias voltage is present.
Use a 50k
high when POK goes high impedance.
The MAX881R features a shutdown mode that reduces
supply current to less than 1µA over temperature. SHDN
is an active-low, logic-level input. Start-up time coming
out of shutdown mode is typically 0.5ms. OUT and
NEGOUT are switched to GND in shutdown mode.
Low-Noise Bias Supply in µMAX
with Power-OK for GaAsFET PA
Figure 2. Using the
6
_______________________________________________________________________________________
MAX881R
or larger pull-up resistor to signal a logic
OUT
POK
POK Function
C4
Detailed Description
TO PA
GATE BIAS
IN
) is inverted to a negative
100k
Power-OK Signal
Shutdown Mode
POWER AMPLIFIER
V
CC
FOR
P
TO
POWER
AMPLIFIER
OUT
IN
is
Select either a fixed or adjustable output for the
MAX881R. Connect FB to GND for a fixed -2V output
(Figure 3). Select an alternative output voltage by con-
necting FB to the midpoint of a resistor-divider from
OUT to GND (Figure 4). When operating under full load
(4mA), the voltage at IN should be at least 0.6V higher
than the absolute voltage required at OUT. Note that
the minimum input voltage required for operation is
2.5V, regardless of the desired output voltage.
Choose R1 to be between 100k
culate R2. For greater accuracy, use resistors with 1%
or better tolerance.
Figure 3a. Standard Application Circuit for Minimum Capacitor
Values
Figure 3b. Standard Application Circuit for Minimum Output
Noise
ON
ON
0.22 F
0.22 F
1 F
OFF
OFF
1 F
C1
C1
C2
C2
Applications Information
R2 = R1 (2 x
C1+
C1-
SHDN
NEGOUT
C1+
C1-
SHDN
NEGOUT
Setting the Output Voltage
MAX881R
MAX881R
GND
GND
V
V
IN
IN
IN
IN
|
V
FB
FB
OUT
OUT
POK
OUT
POK
|
and 400k
- 1)
C4
10 F
C3
1 F
C4
4.7 F
C3
0.22 F
V
V
OUT
OUT
and cal-
= -2V
= -2V