CY7C68300B-56PVXC Cypress Semiconductor Corp, CY7C68300B-56PVXC Datasheet - Page 19
![no-image](/images/manufacturer_photos/0/1/179/cypress_semiconductor_corp_sml.jpg)
CY7C68300B-56PVXC
Manufacturer Part Number
CY7C68300B-56PVXC
Description
IC USB 2.0 BRIDGE BULK 56SSOP
Manufacturer
Cypress Semiconductor Corp
Series
CY7Cr
Specifications of CY7C68300B-56PVXC
Operating Temperature
0°C ~ 70°C
Controller Type
USB 2.0 Controller
Interface
I²C
Voltage - Supply
3.15 V ~ 3.45 V
Current - Supply
50mA
Mounting Type
Surface Mount
Package / Case
56-SSOP
Data Rate
480Mbps
Supply Voltage Range
3.15V To 3.45V
Operating Temperature Range
-40°C To +85°C
Digital Ic Case Style
SSOP
No. Of Pins
56
Operating Temperature Max
85°C
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
CY7C68300B-56PVXC
Manufacturer:
CYPRESS/赛普拉斯
Quantity:
20 000
Table 8-6. EEPROM Organization
Document 38-08033 Rev. *D
AT2LP Configuration
0x00
0x01
0x02
0x03
0x04
0x05
EEPROM
Address
I
I
APM Value
Unused
bVSCBSignature Value
Reserved
Enable mode page 8
Disable wait for INTRQ
BUSY Bit Delay
Short Packet Before Stall
SRST Enable
Skip Pin Reset
2
2
C EEPROM signature byte 0 I
C EEPROM signature byte 1 I
Field Name
CY7C68300A compatibility mode, these bytes should be set
to 0x4D4D.
ATA Device Automatic Power Management Value. If an
attached ATA device supports APM and this field contains
other than 0x00, the AT2LP will issue a SET_FEATURES
command to Enable APM with this value during the drive
initialization process. Setting APM Value to 0x00 disables
this functionality. This value is ignored with ATAPI devices.
Value in the first byte of the CBW CB field that designates
that the CB is to be decoded as vendor specific ATA
commands instead of the ATAPI command block. See
section 7.0 for more detail on how this byte is used.
Bits (7:6)
Bit (5)
Set to 1 to enable the write caching mode page (page 8). If
this page is enabled, Windows will disable write caching by
default which will limit write performance.
Bit (4)
Set to 1 to poll status register rather than waiting for INTRQ.
Setting this bit to 1 will improve USB BOT test results but
may introduce compatibility problems with some devices.
Bit (3)
Enables a delay of up to 120 ms at each read of the DRQ
bit where the device data length does not match the host
data length. This allows the CY7C68300B/CY7C68301B to
work with most devices that incorrectly clear the BUSY bit
before a valid status is present.
Bit (2)
Determines if a short packet is sent prior to the STALL of an
IN endpoint. The USB Mass Storage Class Bulk-Only Speci-
fication allows a device to send a short or zero-length IN
packet prior to returning a STALL handshake for certain
cases. Certain host controller drivers may require a short
packet prior to STALL.
1 = Force a short packet before STALL.
0 = Don’t force a short packet before STALL.
Bit (1)
Determines if the AT2LP is to do an SRST reset during drive
initialization. At least one reset must be enabled. Do not set
SRST to 0 and Skip Pin Reset to 1 at the same time.
1 = Perform SRST during initialization.
0 = Don’t perform SRST during initialization.
Bit (0)
Skip ARESET# assertion. When this bit is set, the AT2LP
will bypass ARESET# during any initialization other than
power up. Do not set SRST to 0 and Skip Pin Reset to 1 at
the same time.
0 = Allow ARESET# assertion for all resets.
1 = Disable ARESET# assertion except for power-on reset
cycles.
2
2
C EEPROM signature byte 0. This byte must be 0x53. For
C EEPROM signature byte 1. This byte must be 0x4B
Field Description
CY7C68300B/CY7C68301B
CY7C68320/CY7C68321
Required
Contents
0x53
0x4B
Page 19 of 36
Suggested
Contents
0x00
0x80
0x24
0x07