MAX1639ESE Maxim Integrated Products, MAX1639ESE Datasheet - Page 9
![no-image](/images/manufacturer_photos/0/4/417/maxim_integrated_products_sml.jpg)
MAX1639ESE
Manufacturer Part Number
MAX1639ESE
Description
DC/DC Switching Controllers
Manufacturer
Maxim Integrated Products
Datasheet
1.MAX1639ESE.pdf
(13 pages)
Specifications of MAX1639ESE
Number Of Outputs
1
Output Voltage
1.1 V to 4.5 V
Input Voltage
4.5 V to 5.5 V
Mounting Style
SMD/SMT
Package / Case
SOIC-16
Maximum Operating Temperature
+ 85 C
Minimum Operating Temperature
- 40 C
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
MAX1639ESE
Manufacturer:
MAXIM
Quantity:
9 447
Part Number:
MAX1639ESE
Manufacturer:
MAXIM/美信
Quantity:
20 000
Company:
Part Number:
MAX1639ESE+
Manufacturer:
Maxim Integrated Products
Quantity:
135
Company:
Part Number:
MAX1639ESE+
Manufacturer:
NS
Quantity:
126
Part Number:
MAX1639ESE+
Manufacturer:
MAXIM/美信
Quantity:
20 000
Gate-drive voltage for the high-side N-channel switch
is generated using a flying-capacitor boost circuit
(Figure 3). The capacitor is alternately charged from
the +5V supply and placed in parallel with the high-
side MOSFET’s gate and source terminals.
Gate-drive resistors (R3 and R4) can often be useful to
reduce jitter in the switching waveforms by slowing
down the fast-slewing LX node and reducing ground
bounce at the controller IC. However, switching loss
may increase. Low-value resistors from around 1Ω to
5Ω are sufficient for many applications.
The current-sense circuit resets the main PWM latch
and turns off the high-side MOSFET switch whenever
the voltage difference between CSH and CSL from cur-
rent through the sense resistor (R1) exceeds the peak
current limit (100mV typical).
Current-mode control provides cycle-by-cycle current-
limit capability for maximum overload protection.
During normal operation, the peak current limit set by
the current-sense resistor determines the maximum
output current. When the output is shorted, the peak
current may be higher than the set current limit due to
delays in the current-sense comparator. Thus, foldback
current limiting is employed where the set current-limit
point is reduced from 100mV to 38mV as the output
(feedback) voltage falls (Figure 4). When the short-
circuit condition is removed, the feedback voltage will
rise and the current-limit voltage will revert to 100mV.
The foldback current-limit circuit is designed to ensure
startup into a resistive load.
The common-mode input range of the current-sense
inputs (CSH and CSL) extends to V
to configure the circuit with the current-sense resistor
on the input side rather than on the load side (Figure 5).
This configuration improves efficiency by reducing the
power dissipation in the sense resistor according to the
duty ratio.
In the high-side configuration, if the output is shorted
directly to GND through a low-resistance path, the
current-sense comparator may be unable to enforce a
current limit. Under such conditions, circuit parasitics
such as MOSFET R
circuit current to a value around the peak-current-
limit setting.
BST High-Side Gate-Driver Supply
Synchronous Rectification for CPU Power
and Overload Current Limiting
_______________________________________________________________________________________
High-Side Current Sensing
DS(ON)
High-Speed Step-Down Controller with
and MOSFET Drivers
typically limit the short-
CC
Current Sense
, so it is possible
Attach a lowpass-filter network between the current-
sense pins and resistor to reduce high-frequency
common-mode noise. The filter should be designed
with a time constant of around one-fifth of the on-time
(130ns at 600kHz, for example). Resistors in the 20Ω to
100Ω range are recommended for R9 and R10.
Connect the filter capacitors C9 and C10 from V
CSH and CSL, respectively.
Values of 39Ω and 3.3nF are suitable for many
designs. Place the current-sense filter network close to
the IC, within 0.1 in (2.5mm) of the CSH and CSL pins.
Figure 4. Foldback Current Limit
Figure 3. Boost Supply for Gate Drivers
CONTROL AND
DRIVE LOGIC
TRANSLATOR
LEVEL
MAX1639
100
90
80
70
60
50
40
30
20
10
0
0
10
20 30
BST
DH
LX
DL
PGND
V
40 50 60 70 80 90 100
DD
V
R4
FB
R3
(%)
V
IN
= 5V
N1
N2
D2
R3 AND R4
ARE OPTIONAL
C3
L1
CC
C1
to
9