DP83934CVUL-20 National Semiconductor, DP83934CVUL-20 Datasheet - Page 52
![no-image](/images/manufacturer_photos/0/4/469/national_semiconductor_sml.jpg)
DP83934CVUL-20
Manufacturer Part Number
DP83934CVUL-20
Description
IC CTRLR ORIENT NETWORK 160PQFP
Manufacturer
National Semiconductor
Datasheet
1.DP83934AVQB.pdf
(104 pages)
Specifications of DP83934CVUL-20
Controller Type
Network Interface Controller (NIC)
Interface
Twisted Pair
Voltage - Supply
4.75 V ~ 5.25 V
Current - Supply
140mA
Operating Temperature
0°C ~ 70°C
Mounting Type
Surface Mount
Package / Case
160-MQFP, 160-PQFP
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Other names
*DP83934CVUL-20
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
DP83934CVUL-20
Manufacturer:
Texas Instruments
Quantity:
10 000
6 0 SONIC-T Registers
6 3 8 Transmit Registers
The transmit registers described in this section are part of
the User Register set The UTDA and CTDA must be initial-
ized prior to issuing the transmit command (setting the TXP
bit) in the Command register
Upper Transmit Descriptor Address Register (UTDA)
This register contains the upper address bits (A
for accessing the transmit descriptor area (TDA) and is con-
catenated with the contents of the CTDA when the SONIC-
T accesses the TDA in system memory The TDA can be as
large as 32k words or 16k long words and can be located
anywhere in system memory This register is unaffected by
a hardware or software reset
Current Transmit Descriptor Address Register (CTDA)
The 16-bit CTDA register contains the lower address bits
(A
initialization this register must be programmed with the low-
er address bits of the transmit descriptor The SONIC-T
concatenates the contents of this register with the contents
of the UTDA to point to the transmit descriptor For 32-bit
memory systems bit 1 corresponding to address signal A1
must be set to ‘‘0’’ for alignment to long-word boundaries
Bit 0 of this register is the End of List (EOL) bit and is used
to denote the end of the list This register is unaffected by a
hardware or software reset
6 3 9 Receive Registers
The receive registers described in this section are part of
the User Register set A software reset has no effect on
these registers and a hardware reset only affects the EOBC
and RSC registers The receive registers must be initialized
prior to issuing the receive command (setting the RXEN bit)
in the Command register
Upper Receive Descriptor Address Register (URDA)
This register contains the upper address bits (A
for accessing the receive descriptor area (RDA) and is con-
catenated with the contents of the CRDA when the
SONIC-T accesses the RDA in system memory The RDA
can be as large as 32k words or 16k long words and can be
located anywhere in system memory This register is unaf-
fected by a hardware or software reset
Current Receive Descriptor Address Register (CRDA)
The CRDA is a 16-bit read write register used to locate the
received packet descriptor block within the RDA It contains
the lower address bits (A
nates the contents of the CRDA with the contents of the
URDA to form the complete 32-bit address The resulting
32-bit address points to the first field of the descriptor block
For 32-bit memory systems bit 1 corresponding to address
signal A1 must be set to ‘‘0’’ for alignment to long-word
boundaries Bit 0 of this register is the End of List (EOL) bit
and is used to denote the end of the list This register is
unaffected by a hardware or software reset
End of Buffer Word Count Register (EOBC)
SONIC-T uses the contents of this register to determine
where to place the next packet At the end of packet recep-
tion the SONIC-T compares the contents of the EOBC reg-
ister with the contents of the Remaining Buffer Word Count
registers (RBWC0 1) to determine whether (1) to place the
next packet in the same RBA or (2) to place the next packet
in another RBA If the EOBC is less than or equal to the
remaining number of words in the RBA after a packet is
received (i e EOBC
next packet in the same RBA If the EOBC is greater than
k
15 1
l
) of the 32-bit transmit descriptor address During
s
RBWC0 1) the SONIC-T buffers the
k
15 1
l
) The SONIC-T concate-
(Continued)
k
k
31 16
31 16
The
l
l
)
)
52
the remaining number of words in the RBA after the packet
is received (i e EOBC
RBA bit LPKT in the Receive Control Register Section
6 3 3 is set and the SONIC-T fetches the next resource
descriptor Hence the next packet received will be buffered
in a new RBA A hardware reset sets this register to 02F8H
(760 words or 1520 bytes) See Sections 5 4 2 and 5 4 4 4
for more information about using EOBC
Upper Receive Resource Address Register (URRA) The
URRA is a 16-bit read write register It is programmed with
the base address of the receive resource area (RRA) This
16-bit upper address value (A
resource area in system memory SONIC-T uses the URRA
register when accessing the receive descriptors within the
RRA by concatenating the lower address value from one of
four receive resource registers (RSA REA RWP or RRP)
Resource Start Address Register (RSA) The RSA is a
15-bit read write register The LSB is not used and always
reads back as a 0 The RSA is programmed with the lower
15 bits (A
resource area SONIC-T concatenates the contents of this
register with the contents of the URRA to form the complete
32-bit address
Resource End Address Register (REA) The REA is a
15-bit read write register The LSB is not used and always
reads back as a 0 The REA is programmed with the lower
15 bits (A
resource area SONIC-T concatenates the contents of this
register with the contents of the URRA to form the complete
32-bit address
Resource Read Pointer Register (RRP) The RRP is a
15-bit read write register The LSB is not used and always
reads back as a 0 The RRP is programmed with the lower
15-bit address (A
scriptor the SONIC-T will read SONIC-T concatenates the
contents of this register with the contents of the URRA to
form the complete 32-bit address
Resource Write Pointer Register (RWP) The RWP is a
15-bit read write register The LSB is not used and always
reads back as a 0 The RWP is programmed with the lower
15-bit address (A
system can add a descriptor SONIC-T concatenates the
contents of this register with the contents of the URRA to
form the complete 32-bit address In 32-bit mode bit 1 cor-
responding to address signal A1 must be zero to insure the
proper equality comparison between this register and the
RRP register
Receive Sequence Counter Register (RSC) This is a
16-bit read write register containing two fields (Figure 6-11)
The SONIC-T uses this register to provide status informa-
tion on the number of packets within a RBA and the number
of RBAs The RSC register contains two 8-bit (modulo 256)
counters After each packet is received the packet se-
quence number is incremented The SONIC-T maintains a
single sequence number for each RBA When the SONIC-T
uses the next RBA the packet sequence number is reset to
zero and the RBA sequence number is incremented This
register is reset to 0 by a hardware reset or by writing zero
to it A software reset has no affect
15
RBA Sequence Number
FIGURE 6-11 Receive Sequence Counter Register
(Modulo 256)
k
k
15 1
15 1
l
l
k
k
) of the starting address of the receive
) of the ending address of the receive
15 1
15 1
l
l
l
8
) of the next available location the
) of the first field of the next de-
RBWC0 1) the Last Packet in
k
7
Packet Sequence Number
31 16
(Modulo 256)
l
) locates the receive
0