VR25000001005JR500 BC Components / Vishay, VR25000001005JR500 Datasheet - Page 5

• Manufacturer Part Number: VR25000001005JR500
• Description: Resistor; Metal Film; Res 10 Megohms; Pwr-Rtg 0.25 W; Tol 5%; Axial; Ceramic Housed
• Manufacturer: BC Components / Vishay

Specifications of VR25000001005JR500

• Brand/series: VR25 Series
• Diameter, Lead Wire: 0.58 ± 0.05 in.
• Dielectric Strength: 700 V
• Dimensions: 7.2 in. L (Max.) x 2.5 in. Dia. (Max.)
• Material, Element: Metal Film
• Package Type: Ceramic Housed
• Power, Rating: 0.25 W
• Resistance: 10 Megohms
• Temperature, Operating: -55 to +155 °C
• Termination: Axial
• Tolerance: ±5 %
• Voltage, Rating: 1.6k
• Lead Free Status / Rohs Status: RoHS Compliant part

VR25
Vishay BCcomponents
TESTS AND REQUIREMENTS
Essentially all tests are carried out in accordance with the
schedule
LCT/UCT/56 (rated temperature range: Lower Category
Temperature, Upper Category Temperature; damp heat,
long
requirements specified by EIA and EIAJ.
The tests are carried out in accordance with IEC publication
60068-2, “Recommended basic climatic and mechanical
robustness testing procedure for electronic components” and
www.vishay.com
200
TEST PROCEDURES AND REQUIREMENTS
IEC
60115-1
CLAUSE
4.16
4.16.2
4.16.3
4.16.4
4.17
4.18
4.19
4.20
4.22
term, 56 days).
of
METHOD
60068-2
21 (Ua1)
21 (Ub)
14 (Na)
21 (Uc)
20 (Tb)
29 (Eb)
TEST
20 (Ta)
21 (U)
6 (Fc)
IEC
“IEC publication
The
rapid change of temperature
robustness of terminations:
bending half number
testing
tensile all samples
torsion other half
soldering heat
For technical questions, contact: [e-mail]
resistance to
solderability
of samples
of samples
vibration
TEST
60115-1”,
bump
High Voltage (up to 1.6 kV) Resistors
also
High Ohmic (up to 22 MΩ)/
covers
category
1.5 mm or acceleration 10 g; 3 directions;
the
frequency 10 to 500 Hz; displacement
3 x 1500 bumps in 3 directions; 40 g
3 x 360° in opposite directions
30 min at + 155 °C; 5 cycles
Ø 0.6 mm; load 5 N; 4 x 90°
thermal shock: 3 s; 350 °C;
Ø 0.6 mm; load 10 N; 10 s
30 min at - 55 °C and
under standard atmospheric conditions according to
“IEC 60068-1”, subclause 5.3.
In the Test Procedures and Requirements table the tests and
requirements are listed with reference to the relevant clauses
of
description of the test procedure is also given. In some
instances deviations from the IEC recommendations were
necessary for our method of specifying.
All soldering tests are performed with mildly activated flux.
total 6 h (3 x 2 h)
3 mm from body
PROCEDURE
2 s; 235 °C
“IEC publications 60115-1 and 60068-2”;
ΔR max.: ± (0.5 % R + 0.05 Ω)
ΔR max.: ± (0.5 % R + 0.05 Ω)
ΔR max.: ± (0.5 % R + 0.05 Ω)
ΔR max.: ± (0.5 % R + 0.05 Ω)
ΔR max.: ± (0.5 % R + 0.05 Ω)
number of failures < 10 x 10
number of failures < 10 x 10
good tinning; no damage
REQUIREMENTS
Document Number: 28732
no damage
no damage
no damage
Revision: 21-Feb-08
a
short
-6
-6