D-B54 SMC Corporation, D-B54 Datasheet - Page 94
![no-image](/images/no-image-200.jpg)
D-B54
Manufacturer Part Number
D-B54
Description
Sensor, reed switch, band mount, grommet connection, for NCM cylinders
Manufacturer
SMC Corporation
Type
Hall Effectr
Datasheet
1.D-A93.pdf
(95 pages)
Specifications of D-B54
Body Style
Rectangular
Function
Proximity
Primary Type
Proximity
Technology
Reed
Series
Mounting and Moving Method of Auto Switch
Direct Mounting to the Round Groove
∗ Equivalent inch size.
Note) When the auto switch is mounted onto the CDBQ2 end lock type,
Mounting and Moving Method of D-P3DW (1)
q Insert the protrusion on the bottom of the auto switch into the mating part
w Insert the temporarily tightened mounting bracket into the mating
e Check the detecting position of the auto switch and fix the auto switch
r If the detecting position is changed, go back to step w.
∗ The hexagon socket head cap screw (M2.5 x 6 L) is used to fix the mounting
Note 1) Ensure that the auto switch is covered with the mating groove to protect
Note 2) The torque for tightening the hexagon socket head cap screw (M2.5 x 6 L,
Note 3) Tighten the hexagon socket head cap screws evenly.
Precautions for the Cylinder/Actuator Mounting
• When mounting the D-P3DW onto a cylinder/actuator with ø1.26 to
• In the CDQSø0.98 and CDLQø0.98, the auto switch will interfere with
7
Compact cylinder
Compact cylinder with lock
Pin clamp cylinder
Pin clamp cylinder with lock
ø1.97, to avoid mutual interference, use a fitting with width across flats
0.47 inch or less for ø1.26 and ø1.58, and use a fitting with width across
flats 0.55 inch or less for ø1.97. Also, if the corner of the fitting interferes
with the housing of the auto switch, adjust the tightening of the fitting to
eliminate the interference. In the case of interference with an elbow type
fitting, direct the port of the fitting away from the auto switch. Such
interference must be avoided especially when a speed controller and
speed exhaust controller with a fitting are selected.
the fitting if mounted onto the face with the port, so it needs to be
mounted on a different face.
bracket and cylinder/actuator.
This enables the replacement of the auto switch without adjusting the auto
switch position.
of the auto switch mounting bracket and fix the auto switch and the auto
switch mounting bracket temporarily by tightening the hexagon socket
head cap screw (M2.5 x 9 L) 1 to 2 turns.
groove of the cylinder/actuator, and slide the auto switch onto the
cylinder/actuator through the groove.
firmly with the hexagon socket head cap screw (M2.5 x 6 L, M2.5 x 9 L). ∗
please contact SMC.
the auto switch.
M2.5 x 9 L) is 1.77 to 2.66 in-lb.
Hexagon socket head cap screw
(M2.5 x 6 L)
Hexagon socket head cap screw
(M2.5 x 9 L)
D-P3DW
Applicable cylinder/actuator
CDQS
CDQ2
CDLQ
CKQG
CLKQG
ø32 to ø100 (ø1.26 to ø3.94) ∗
ø25 to ø100 (ø0.98 to ø3.94) ∗
ø25 (ø0.98) ∗
ø50 (ø1.97) ∗
ø50 (ø1.97) ∗
Auto switch mounting bracket
Note) When the auto switch
mounting bracket is
ordered by its part number,
it includes the bracket and
screws in the dashed line.
BQ3-032S
Convex part
mounting bracket
BQ3-032S
Note)
Auto switch
part no.
∗ Equivalent inch size.
Note) For the MGP end lock type, as the auto switch cannot be mounted
Mounting and Moving Method of D-P3DW (2)
q Insert the protrusion on the bottom of the auto switch into the mating
w Insert the temporarily tightened mounting bracket into the mating
e Check the detecting position of the auto switch and fix the auto
r If the detecting position is changed, go back to step w.
∗ The hexagon socket head cap screw (M2.5 x 6 L) is used to fix the
Note 1) Ensure that the auto switch is covered with the mating groove to
Note 2) The torque for tightening the hexagon socket head cap screw (M2.5
Note 3) Tighten the hexagon socket head cap screws evenly.
Direct Mounting to the Square Groove
Compact guide cylinder
Compact guide cylinder with lock
mounting bracket and cylinder/actuator.
This enables the replacement of the auto switch without adjusting the auto
switch position.
part of the auto switch mounting bracket and fix the auto switch and
the auto switch mounting bracket temporarily by tightening the
hexagon socket head cap screw (M2.5 x 9 L) 1 to 2 turns.
groove of the cylinder/actuator, and slide the auto switch onto
the cyinder/actuator through the groove.
switch firmly with the hexagon socket head cap screw (M2.5 x 6
L, M2.5 x 9 L). ∗
onto the lock mechanism face, mount it to the groove on the bottom
of the lock mechanism face.
protect the auto switch.
x 6 L, M2.5 x 9 L) is 1.77 to 2.66 in-lb.
Hexagon socket head cap screw
(M2.5 x 9 L)
Hexagon socket head cap screw
(M2.5 x 6 L)
Applicable cylinder/actuator
MGP
MGPS
MLGP
ø25 to ø100 (ø0.98 to ø3.94) ∗
ø25 to ø100 (ø0.98 to ø3.94) ∗
ø50
Note) When the auto switch mounting
,
ø80 (ø1.97
bracket is ordered by its part
number, it includes the bracket
and screws in the dashed line.
Auto switch mounting bracket
,
ø3.15) ∗
BMG5-025S
Convex part
mounting bracket
BMG5-025S
Auto switch
part no.
Note)