KSZ8041TL Micrel Inc, KSZ8041TL Datasheet - Page 37

• Manufacturer Part Number: KSZ8041TL
• Description: TRANSCEIVER 10/100BASE 48-TQFP
• Manufacturer: Micrel Inc
• Type: Transceiverr

Specifications of KSZ8041TL

• Package / Case: 48-TQFP, 48-VQFP
• Number Of Drivers/receivers: 1/1
• Protocol: MII, RMII
• Voltage - Supply: 3.135 V ~ 3.465 V
• Mounting Type: Surface Mount
• Supply Voltage Range: 3.3V
• Logic Case Style: TQFP
• No. Of Pins: 48
• Svhc: No SVHC (15-Dec-2010)
• Base Number: 804
• Supply Voltage Max: 3.3V
• Termination Type: SMD
• Development Tool: RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 576-3295 - BOARD EVALUATION KSZ8041TL
• Lead Free Status / RoHS Status: Compliant, Lead free / RoHS Compliant
• Other names: 576-1619

Micrel, Inc.
100Base-FX Fiber Operation (KSZ8041FTL only)
100Base-FX fiber operation is similar to 100Base-TX copper operation with the differences being that the scrambler/de-
scrambler and MLT3 encoder/decoder are bypassed on transmission and reception. In addition, auto-negotiation is
bypassed, auto MDI/MDI-X is disabled, and speed is set to 100Mbps. The duplex can be set to either half or full. Usually,
it is set to full-duplex.
Fiber Signal Detect
In 100Base-FX operation, FXSD (fiber signal detect), input pin 48, is usually connected to the fiber transceiver SD (signal
detect) output pin. 100Base-FX mode is activated when the FXSD input pin is greater than 1V. When FXSD is between
1V and 1.8V, no fiber signal is detected and a Far-End Fault is generated. When FXSD is over 2.2V, the fiber signal is
detected.
100Base-FX mode and signal detection is summarized in the following table:
To ensure proper operation, a resistive voltage divider is recommended to adjust the fiber transceiver SD (signal detect)
output voltage swing to match the FXSD pin’s input voltage threshold.
Alternatively, the Far-End Fault feature can be disabled. In this case, the FXSD input pin is tied high to 3.3V to force
100Base-FX mode.
Far-End Fault
A Far-End Fault (FEF) occurs when the signal detection is logically false on the receive side of the fiber transceiver. The
KSZ8041FTL detects a FEF when its FXSD input (pin 48) is between 1V and 1.8V. When a FEF is detected, the
KSZ8041FTL signals its fiber link partner that a FEF has occurred by transmitting a repetitive pattern of 84-ones and 1-
zero. This pattern is used to inform the fiber link partner that there is a faulty link on its transmit side.
By default, FEF is enabled. FEF is disabled by strapping “no FEF” (pin 43) low. See “Strapping Options” section for detail.
December 2009
FXSD Input Voltage
Less than 0.2V
Greater than 1V, but less than 1.8V
Greater than 2.2V
Table 11. Copper and Fiber Mode Selection
Fiber mode
Mode
Copper mode
No signal detected
Far-End Fault generated (if enabled)
Fiber mode
Signal detected
37
KSZ8041TL/FTL/MLL
M9999-120909-1.2