DP-110-GRAY 3M, DP-110-GRAY Datasheet - Page 7

• Manufacturer Part Number: DP-110-GRAY
• Description: Adhesive; Epoxy; Gray; Duo-Pak; 1.7 Fluid Ounce Tube
• Manufacturer: 3M

Specifications of DP-110-GRAY

• Chemical Component: Butadiene/Epoxy Resin/Hydrogenated Polyphenyls/Hydrogenated Terphenyl/Methacrylate/Styrene Polymer
• Chemical System: Epoxy
• Color: Gray
• Dispensing Method: Syringe
• Primary Type: Adhesive
• Time, Drying: Air Dry for 15 minutes, Force Dry for 10 minutes @ 66 °C +⁄- 23 °C (Aluminum Surface), If 3M™ Scotch-Weld™ Structural Adhesive Primer EC1945 B⁄A is Used, Apply a Thin Coating (0.5 mils) on the Metal Surfaces to be Bonded, Air Dry for 60 minutes, then Cure
• Time, Setting: 15 min. (Aluminum), 60 min. (Steel)
• Weight: 1.7 fl.oz.
• Lead Free Status / Rohs Status: RoHS Compliant part

8.1 ENGINEERING CONTROLS
Provide appropriate local exhaust for cutting, grinding, sanding or machining. Use general dilution ventilation and/or local exhaust
ventilation to control airborne exposures to below Occupational Exposure Limits and/or control dust, fume, or airborne particles. If
ventilation is not adequate, use respiratory protection equipment.
8.2 PERSONAL PROTECTIVE EQUIPMENT (PPE)
8.2.1 Eye/Face Protection
Avoid eye contact.
The following eye protection(s) are recommended: Safety Glasses with side shields, Indirect Vented Goggles.
8.2.2 Skin Protection
Avoid skin contact.
Select and use gloves and/or protective clothing to prevent skin contact based on the results of an exposure assessment. Consult with
your glove and/or protective clothing manufacturer for selection of appropriate compatible materials.
Gloves made from the following material(s) are recommended: Neoprene, Nitrile Rubber.
8.2.3 Respiratory Protection
Avoid breathing of vapors. Avoid breathing of dust created by cutting, sanding, grinding or machining.
Select one of the following NIOSH approved respirators based on airborne concentration of contaminants and in accordance with
OSHA regulations: Half facepiece or fullface air-purifying respirator with organic vapor cartridges and P95 particulate prefilters,
Half facepiece or fullface air-purifying respirator with organic vapor cartridges and N95 particulate prefilters, Half facepiece or
fullface air-purifying respirator with organic vapor cartridges and P100 particulate prefilters. Consult the current 3M Respiratory
Selection Guide for additional information or call 1-800-243-4630 for 3M technical assistance.
8.2.4 Prevention of Swallowing
Do not eat, drink or smoke when using this product. Wash exposed areas thoroughly with soap and water.
8.3 EXPOSURE GUIDELINES
SOURCE OF EXPOSURE LIMIT DATA:
_________________________________________________________________________________________________
Hydrogenated Terphenyl
Hydrogenated Terphenyl
MATERIAL SAFETY DATA SHEET 3M(TM) Scotch-Weld(TM) Epoxy Adhesive DP-110, Gray (Part B) or 3M(TM) Scotch-Weld(TM)
Epoxy Adhesive 110 B/A, Gray (Part B)
Ingredient
SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION
SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES
ACGIH: American Conference of Governmental Industrial Hygienists
CMRG: Chemical Manufacturer Recommended Guideline
OSHA: Occupational Safety and Health Administration
AIHA: American Industrial Hygiene Association Workplace Environmental Exposure Level (WEEL)
Specific Physical Form:
Odor, Color, Grade:
General Physical Form:
Autoignition temperature
ACGIH
OSHA
Authority
TWA
TWA
Type
Paste
White, very slight odor.
Liquid
No Data Available
0.5 ppm
0.5 ppm
Limit
Table Z-1A
Additional Information
Page 4 of 8