595D226X0050R2T Sprague / Vishay, 595D226X0050R2T Datasheet - Page 11

• Manufacturer Part Number: 595D226X0050R2T
• Description: Capacitor, Tantalum; 22uF; Chip; +/-20%; Case R; SMD; 50WVDC; 65V; 0.39Ohms ESR; 11muA; 6
• Manufacturer: Sprague / Vishay

Specifications of 595D226X0050R2T

• Capacitance: 22 μF
• Case Code: R
• Case Size: 7257
• Current, Dc Leakage: 11 μA
• Dimensions: 0.283 in. L (Max.) x 0.235 in. ± 0.012 in. W x 0.136 in. ± 0.012 in. H
• Dissipation Factor: 6% (Max.) @ 120 Hz, +25°C
• Esr: 0.39 Ohms
• Esr, Test Condition: @ +25°C, 100 kHz
• Material, Element: Tantalum
• Standards: EIA 535BAAC and CECC30801
• Temperature, Operating, Maximum: 85 °C
• Temperature, Operating, Minimum: -55 °C
• Termination: SMT
• Tolerance: ±20 %
• Voltage, Rating: 50 VDC
• Voltage, Surge: 65 VDC
• Terminations: 100% Tin (2) Standard
• Capacitance Range: 0.1 μF to 1500 μF
• Lead Free Status / Rohs Status: RoHS Compliant part

595D
Vishay Sprague
www.vishay.com
66
Notes:
1. A
2. Tape with components shall pass around radius "R" without damage. The minimum trailer length may require additional length to
3. This dimension is the flat area from the edge of the sprocket hole to either the outward deformation of the carrier tape between the
4. This dimension is the flat area from the edge of the carrier tape opposite the sprocket holes to either the outward deformation of the
5. The embossment hole location shall be measured from the sprocket hole controlling the location of the embossment. Dimensions of
6. B
Concentric around B
TAPE AND REEL PACKAGING in inches [millimeters]
Note: Metric dimensions will govern. Dimensions in inches are rounded and for reference only.
Double Pitch
For Tape Feeder
B
Reference only
including draft.
dimensions of the component. The clearance between the ends of the terminals or body of the component to the sides and depth of
the cavity (A
rotation of the component within the cavity of not more than 20 degrees.
provide R minimum for 12mm embossed tape for reels with hub diameters approaching N minimum.
embossed cavities or to the edge of the cavity whichever is less.
carrier tape between the embossed cavity or to the edge of the cavity whichever is less.
embossment location and hole location shall be applied independent of each other.
(Note 6)
0
B
.024 [0.600]
0
1
1
12mm
12mm
TAPE
(Top View)
B
(Note 5)
SIZE
8mm
Max.
dimension is a reference dimension for tape feeder clearance only.
0
Max.
K
A
0
0
are determined by the maximum dimensions to the ends of the terminals extending from the component body and/or the body
Component Rotation
0
Max.
20
.004 [0.10]
B
Component
Center Line
T
0
Component
Center Line
°
2
0
Max.
Typical
K
Cavity
Maximum
Typical
B
0
(Note 6)
) must be within .002" [0.05mm] minimum and .020" [0.50mm] maximum. The clearance allowed must also prevent
1
0.179
[4.55]
0.323
0.323
(Max.)
[8.2]
[8.2]
K
0
Cover
Tape
Top
Embossments
Deformation
D
Between
(Note 5)
Cover
Tape
Allowable Camber to be 0.039/3.937 [1/100]
1
0.039
0.059
0.059
Top
[1.0]
[1.5]
[1.5]
(Min.)
Center Lines
Non-Cumulative Over 9.843 [250.0]
3.937 [100.0]
of Cavity
For technical questions, contact [e-mail]
0.039 [1.0]
0.059 + 0.004 - 0.0
Max.
[1.5 + 0.10 - 0.0]
0.138 ± 0.002
0.217 ± 0.002
0.453 ± 0.004
[11.5 ± 0.03]
9.843 [250.0]
[3.5 ± 0.05]
[5.5 ± 0.05]
(Top View)
USER DIRECTION OF FEED
Camber
F
A
0.039 [1.0] Max.
0
B
P
0.157
Tape
[4.0
0
1
±
0.157 ± 0.004
0.157 ± 0.004
0.315 ± 0.004
±
0.10]
[4.0 ± 0.1]
[4.0 ± 0.1]
[8.0 ± 0.1]
0.004
DIRECTION OF FEED
P
1
Cathode (-)
Maximum Cavity
Size (Note 1)
10 Pitches Cumulative
Tolerance on Tape
±
Anode (+)
0.079
0.008 [0.2]
[2.0
Tape and Reel Specifications: All case codes are available
on plastic embossed tape per EIA-481-1. Tape reeling per IEC
286-3 is also available. Standard reel diameter is 7" [178mm]. 13"
[330mm] reels are available and recommended as the most cost
effective packaging method.
The most efficient packaging quantities are full reel increments on
a given reel diameter. The quantities shown allow for the sealed
empty pockets required to be in conformance with E I A - 4 8 1 - 1 .
Reel size and packaging orientation must be specified in the Vishay
Sprague part number.
±
±
0.05]
0.002
(Note 2)
R (Min.)
0.079 x 0.047 [2.0 x 1.2] and Larger.
0.984
[25.0]
1.181
[30.0]
1.181
[30.0]
Min. (Note 3)
0.030 [0.75]
Min. (Note 4)
0.030 [0.75]
D
1
Min. For Components
Embossment
(Note 5)
(Max.)
F
0.098
0.256
0.256
[2.5]
[6.5]
[6.5]
T
0.069
2
[1.75
W
±
±
0.004
0.10]
0.315 + 0.012 - 0.004
[8.0 + 0.3 - 0.1]
0.472 ± 0.012
0.945 ± 0.012
[12.0 ± 0.30]
[24.0 ± 0.03]
Document Number 40007
W
(Side or Front Sectional View)
20
Component
°
Maximum
Revision 07-Mar-05
Rotation
(Note 1)
A
0
B
0
K
0