PIC16F74-I/P Microchip Technology Inc., PIC16F74-I/P Datasheet - Page 77
![no-image](/images/manufacturer_photos/0/4/440/microchip_technology_inc__sml.jpg)
PIC16F74-I/P
Manufacturer Part Number
PIC16F74-I/P
Description
40 PIN, 7 KB FLASH, 192 RAM, 33 I/O
Manufacturer
Microchip Technology Inc.
Datasheet
1.PIC16F74-IP.pdf
(174 pages)
Specifications of PIC16F74-I/P
A/d Inputs
8-Channel, 8-Bit
Cpu Speed
5 MIPS
Eeprom Memory
0 Bytes
Input Output
33
Interface
I2C/SPI/USART
Memory Type
Flash
Number Of Bits
8
Package Type
40-pin PDIP
Programmable Memory
7K Bytes
Ram Size
192 Bytes
Speed
20 MHz
Timers
2-8-bit, 1-16-bit
Voltage, Range
2-5.5 V
Lead Free Status / Rohs Status
RoHS Compliant part
Electrostatic Device
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
PIC16F74-I/P
Manufacturer:
MAXIM
Quantity:
101
Company:
Part Number:
PIC16F74-I/P
Manufacturer:
MICROCHIP
Quantity:
50
Part Number:
PIC16F74-I/P
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
Company:
Part Number:
PIC16F74-I/PT
Manufacturer:
MIC
Quantity:
50
Company:
Part Number:
PIC16F74-I/PT
Manufacturer:
Microchip Technology
Quantity:
10 000
10.2.2
The receiver block diagram is shown in Figure 10-4.
The data is received on the RC7/RX/DT pin and drives
the data recovery block. The data recovery block is
actually a high speed shifter operating at x16 times the
baud rate, whereas the main receive serial shifter oper-
ates at the bit rate, or at F
Once Asynchronous mode is selected, reception is
enabled by setting bit CREN (RCSTA<4>).
The heart of the receiver is the receive (serial) shift reg-
ister (RSR). After sampling the STOP bit, the received
data in the RSR is transferred to the RCREG register (if
it is empty). If the transfer is complete, flag bit RCIF
(PIR1<5>) is set. The actual interrupt can be enabled/
disabled
(PIE1<5>). Flag bit RCIF is a read only bit which is
cleared by the hardware. It is cleared when the RCREG
register has been read and is empty. The RCREG is a
double buffered register (i.e., it is a two deep FIFO). It
FIGURE 10-4:
2002 Microchip Technology Inc.
F
by
RC7/RX/DT
USART ASYNCHRONOUS
RECEIVER
OSC
setting/clearing
Baud Rate Generator
x64 Baud Rate CLK
USART RECEIVE BLOCK DIAGRAM
OSC
SPBRG
Pin Buffer
and Control
SPEN
.
enable
bit
Data
Recovery
Interrupt
RCIE
÷ 64
÷ 16
or
CREN
RCIF
RCIE
is possible for two bytes of data to be received and
transferred to the RCREG FIFO and a third byte to
begin shifting to the RSR register. On the detection of
the STOP bit of the third byte, if the RCREG register is
still full, the overrun error bit OERR (RCSTA<1>) will be
set. The word in the RSR will be lost. The RCREG reg-
ister can be read twice to retrieve the two bytes in the
FIFO. Overrun bit OERR has to be cleared in software.
This is done by resetting the receive logic (CREN is
cleared and then set). If bit OERR is set, transfers from
the RSR register to the RCREG register are inhibited
and no further data will be received, therefore, it is
essential to clear error bit OERR if it is set. Framing
error bit FERR (RCSTA<2>) is set if a STOP bit is
detected as clear. Bit FERR and the 9th receive bit are
buffered the same way as the receive data. Reading
the RCREG will load bits RX9D and FERR with new
values, therefore, it is essential for the user to read the
RCSTA register before reading RCREG register, in
order not to lose the old FERR and RX9D information.
RX9
MSb
STOP
RX9D
(8) 7
OERR
RCREG Register
RSR Register
• • •
8
Data Bus
1
FERR
PIC16F7X
0
START
FIFO
LSb
DS30325B-page 75