VBA40A-T04-Z SMC Corporation, VBA40A-T04-Z Datasheet - Page 5

• Manufacturer Part Number: VBA40A-T04-Z
• Description: BOOSTER REGULATOR, 1/2 NPTF PORT, HANDLE OPERATED TYPE, PSI
• Manufacturer: SMC Corporation

Specifications of VBA40A-T04-Z

• Brand/series: VBA Series
• Flow Rate: 1900 SCFM
• Pressure Adjustment: Handle Operating
• Pressure Increase Ratio: Twice
• Pressure, Operating: 1 MPa
• Proof Pressure: 1.5 MPa
• Size, Port: 1⁄2 in.
• Temperature, Ambient: 2 to 50
• Thread Type: NPTF

Standard Specifications
Note 1) If the OUT pressure is higher than the set pressure by the handle, excess pressure is exhausted from the back of the handle.
Note 2) Flow rate at IN= OUT= 0.5 MPa. The pressure varies depending on the operating conditions. Refer to “Flow-rate Characteristics” on pages 3 and 4.
Options/Part No.
Pressure Gauge, Silencer (When thread type is Rc or G.)
Note 1) In the case of options GN, two pressure gauges and one silencer are included in the same container as accessories.
Note 2) KT-VBA22A-7 is a pressure gauge with fitting. (Please order two units when using with IN and OUT.)
Pressure Gauge, Silencer (When thread type is NPT or NPTF.)
Note 1) In the case of options GN, two pressure gauges and one silencer are included in the same container as accessories.
Note 2) KT-VBA22A-7N, KT-VBA22A-8N are pressure gauges with fittings. (Please order two units when using with IN and OUT.)
Note 3) Under the new measurement law, the pressure unit of “psi” on the pressure gauges cannot be used in Japan.
Note 4) Pressure unit on the pressure gauge: psi
Related Products/Part No.
Mist Separator, Exhaust Cleaner
Note) Refer to page 12 for air tanks, Best Pneumatics No. 5 for mist separators
Description
Description
Pressure gauge
Silencer
High-noise reduction silencer
Elbow for silencer
Pressure gauge ∗: when Nil
Pressure gauge ∗: when “-Z”
Silencer
High-noise reduction silencer
Elbow for silencer
Description
Fluid
Pressure increase ratio
Pressure adjustment mechanism
Max. flow rate
Set pressure range (MPa)
Supply pressure range (MPa)
Proof pressure (MPa)
Port size (Rc)
(IN/OUT/EXH: 3 locations)
Pressure gauge port size (Rc)
(IN/OUT: 2 locations)
Ambient and fluid temperature (°C)
Installation
Lubrication
Weight (kg)
Mist separator
Exhaust cleaner
and Best Pneumatics No. 6 for exhaust cleaners.
Refer to the separate operation manual for the connection method.
Model
Model
Note 2)
(L/min (ANR))
For VBA10A-02
For VBA11A-02
Note 4)
AM250C-02
AMC310-03
Model
Model
G
G
N
S
N
S
L
L
VBA10A-N02 ∗
VBA10A-T02 ∗
VBA10A-F02
KT-VBA10A-18
KT-VBA10A-18N
VBA10A-02
G27-P20-01
AN200-N02
G27-20-01
G27-20-01
AN200-02
∗
ANA1-02
: when “
VBA10A-02
—
For VBA20A-03
For VBA22A-03
Handle-operated with relief mechanism
AM450C-04, 06
0.2 to 2.0
AMC510-06
0.84
230
1/4
-Z
3
”
VBA20A-N03 ∗
VBA20A-T03 ∗
VBA20A-F03
VBA20A-03
AN300-N03
ANA1-N03
AN300-03
∗
ANA1-03
: when “
VBA20A-03
—
—
For VBA40A-04
For VBA42A-04
For VBA43A-04
AM550C-06, 10
AMC610-10
G36-P10-N01
1000
G36-10-N01
3/8
3.9
G36-10-01
-Z
”
0.2 to 1.0
VBA40A-N04 ∗
VBA40A-T04 ∗
VBA40A-F04
VBA40A-04
AN400-N04
ANA1-N04
AN400-04
∗
ANA1-04
: when “
VBA40A-04
—
—
1900
1/2
8.6
Note 1)
1. System configuration
2. Exhaust air measures
3. Maintenance space
-Z
”
• The IN port of the booster regulator has metallic mesh to prevent
• The booster regulator has a sliding part inside, and it generates
• Connect a lubricator to the outlet side, because the accumulated
• Provide a dedicated pipe to release the exhaust air from each
• Depending on the necessity, install a silencer or an exhaust
• Allow the sufficient space for maintenance and inspection.
Twice
VBA22A-N03 ∗
VBA22A-T03 ∗
VBA22A-F03
Caution
dust from entering the booster regulator. However, it cannot
remove dust continuously or separate drainage. Make sure to
install a mist separator (AM series) on the inlet side of the
booster regulator.
dust. Also, install an air purification device such as an air filter or
a mist separator on the outlet side as necessary.
oil in the booster regulator may result in a malfunction.
booster regulator. If exhaust air is converged into a pipe, the
back pressure that is created could cause improper operation.
cleaner on the exhaust port of the booster regulator to reduce
the exhaust noise.
2 to 50 (No freezing)
KT-VBA22A-7N
KT-VBA22A-8N
KT-VBA22A-7
1.5
VBA22A-03
Grease (Non-lube)
AN300-N03
ANA1-N03
Compressed air
AN300-03
∗
ANA1-03
VBA22A-03
: when “
Horizontal
0.1 to 1.0
—
—
Booster Regulator
1000
3/8
1/8
3.9
-Z
Air-operated
0.2 to 1.0
”
VBA42A-N04 ∗
VBA42A-T04 ∗
VBA42A-F04
VBA42A-04
G36-P10-N01
G36-10-N01
AN400-N04
G36-10-01
ANA1-N04
AN400-04
VBA42A-04
∗
ANA1-04
: when “
—
—
1900
8.6
Design
-Z
”
1/2
VBA43A-N04 ∗
VBA43A-T04 ∗
VBA43A-F04
VBA43A-04
G27-P20-N01
G27-20-N01
AN400-N04
VBA43A-04
G27-20-01
ANA1-N04
AN400-04
∗
ANA1-04
Series
0.2 to 1.6
: when “
relief mechanism
Handle-operated with
1600
—
—
2.4
8.6
-Z
”
VBA11A-N02 ∗
VBA11A-T02 ∗
VBA11A-F02
KT-VBA10A-18
KT-VBA10A-18N
VBA11A-02
VBA11A-02
G27-P20-01
AN200-N02
VBA
2 to 4 times
G27-20-01
G27-20-01
AN200-02
∗
ANA1-02
0.2 to 2.0
: when “
Note 1)
0.89
1/4
—
70
3
-Z
2
”