DSPIC30F6015-30I/PT Microchip Technology Inc., DSPIC30F6015-30I/PT Datasheet - Page 177

• Manufacturer Part Number: DSPIC30F6015-30I/PT
• Description: 16 BIT MCU/DSP 64LD 30MIPS 144 KB FLASH
• Manufacturer: Microchip Technology Inc.
• Type: DSPr

Specifications of DSPIC30F6015-30I/PT

• A/d Inputs: 16-Channels, 10-Bit
• Cpu Speed: 30 MIPS
• Eeprom Memory: 4K Bytes
• Input Output: 52
• Interface: CAN, I2C, SPI, UART/USART
• Ios: 52
• Memory Type: Flash
• Number Of Bits: 16
• Package Type: 64-pin TQFP
• Programmable Memory: 144K Bytes
• Ram Size: 8K Bytes
• Timers: 5-16-bit, 2-32-bit
• Voltage, Range: 2.5-5.5
• Lead Free Status / Rohs Status: RoHS Compliant part Electrostatic Device

24.0
This section provides an overview of dsPIC30F electrical characteristics. Additional information will be provided in future
revisions of this document as it becomes available.
For detailed information about the dsPIC30F architecture and core, refer to the “dsPIC30F Family Reference Manual”
(DS70046).
Absolute maximum ratings for the dsPIC30F family are listed below. Exposure to these maximum rating conditions for
extended periods may affect device reliability. Functional operation of the device at these or any other conditions above
the parameters indicated in the operation listings of this specification is not implied.
Absolute Maximum Ratings
Ambient temperature under bias.............................................................................................................-40°C to +125°C
Storage temperature .............................................................................................................................. -65°C to +150°C
Voltage on any pin with respect to V
Voltage on V
Voltage on MCLR with respect to V
Maximum current out of V
Maximum current into V
Input clamp current, I
Output clamp current, I
Maximum output current sunk by any I/O pin..........................................................................................................25 mA
Maximum output current sourced by any I/O pin ....................................................................................................25 mA
Maximum current sunk by all ports .......................................................................................................................200 mA
Maximum current sourced by all ports (Note 2)....................................................................................................200 mA
© 2006 Microchip Technology Inc.
†
device. This is a stress rating only and functional operation of the device at those or any other conditions above those
indicated in the operation listings of this specification is not implied. Exposure to maximum rating conditions for
extended periods may affect device reliability.
NOTICE: Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the
Note 1: Voltage spikes below V
2: Maximum allowable current is a function of device maximum power dissipation. See Table 24-6.
ELECTRICAL CHARACTERISTICS
Thus, a series resistor of 50-100 should be used when applying a “low” level to the MCLR/V
than pulling this pin directly to V
DD
with respect to V
IK
OK
(V
DD
I
SS
(V
< 0 or V
pin (Note 2)................................................................................................................250 mA
O
pin ...........................................................................................................................300 mA
< 0 or V
SS
SS
I
SS
SS
> V
......................................................................................................... -0.3V to +5.5V
(†)
........................................................................................................ 0V to +13.25V
at the MCLR/V
O
(except V
DD
> V
) .......................................................................................................... ±20 mA
SS
DD
.
) ...................................................................................................±20 mA
DD
and MCLR) (Note 1) ..................................... -0.3V to (V
PP
pin, inducing currents greater than 80 mA, may cause latch-up.
dsPIC30F6010A/6015
DS70150B-page 175
PP
DD
pin, rather
+ 0.3V)