71BDF36-01-2-AJN Grayhill Inc, 71BDF36-01-2-AJN Datasheet - Page 9

• Manufacturer Part Number: 71BDF36-01-2-AJN
• Description: Switch, Rotary, 1/4 Inch Shaft, Adjustable Stop, PC Mount, 36 Degree, 1 Deck/2P
• Manufacturer: Grayhill Inc
• Type: Rotaryr

Specifications of 71BDF36-01-2-AJN

• Actuator Type: Shaft
• Current, Rating: 300 mA
• Dielectric Strength: 500 VAC
• Mounting Type: PCB
• Number Of Poles: 2
• Special Features: Adjustable Stop
• Termination: PC Pin
• Voltage, Rating: 115/30 VAC/VDC

SPECIFICATIONS
SPECIFICATIONS: Materials and Finishes
Military Qualification MIL-S-3786/39
The military style of the Series 71 rotary
switch is qualified to MIL- S-3786/39. Complete
electrical rating information is listed on the
following page. The Series 71 rotary switch
qualification includes the 30° and the 36°
angles of throw, in .125" (3,18) and .250"
(6,35) diameter shafts, with solder lug terminals
and printed circuit terminals, in sealed and
unsealed style switches. Standard variations
such as shaft and/or bushing length, etc. that
do not affect the switch performance can also
be marked as qualified product. Contact
Grayhill for complete details.
Dimensionally the military style is the same as
the standard style with the exception of the PC
version of 3 or 4 decks; a spacer deck between
decks 2 and 3 adds another deck length to the
Materials and Finishes
Standard Style
Cover: Diallyl per (MIL-M-14) ASTM-D-
5948 except for 71 BT (see bushing).
Base and Deck Separator: Diallyl per
(MIL-M-14) ASTM-D-5948
Bushing: Zinc casting, cadmium-plated per
ZZ-P-416, Class 2, Type II.
Through Bolts and Nuts, Shaft and
Rear Support Plate, Stop Pins and Stop
Arm (All Others): Stainless steel
Shaft, Stop Plates, Stop Arm (71BT):
Reinforced thermoplastic
Detent Rotor: Reinforced thermoplastic for
71BT; phenolic per (MIL-M-14) ASTM-D-
5948 for all others
Detent Balls: Steel, nickel-plated
Detent Springs: Tinned music wire
Rotor Contact: Silver alloy and beryllium
copper
Base Contacts, Common Plate and
Terminals: Brass, Gold plate .000005"
minimum over Silver plate .00005" over
nickel .00002".
Front Support Plate (71 BT only):
Tempered steel, tin/lead-plated.
Interdeck Seal (71 BT Only): Silicone
Extension: Brass, unplated
Rotor Mounting Plate: Thermoplastic
switch without increasing the number of
operative decks.
Another difference in the standard and military
styles is the mounting hardware. Ordered as
options with a standard style switch these items
are included with the military style switch: non-
turn washer with solder lug style and a non-turn
washer plus a mounting bushing washer with
the PC terminal style.
Complete specification drawings are available
from Grayhill, Inc. for the standard military
qualified products. Military qualified Series 71
rotary switches may be ordered by the “M”
number listed in Military Specification Sheet/39
or by Grayhill part number. All qualified switches
will be marked to the specification.
Mounting Hardware: One mounting nut and
one internal tooth lockwasher are supplied
with each switch. For switches with A in the
style description, the nut is .062" (1,57) thick
by .312" (7,92) across flats. For switches with
B or C in the style description, the nut is .094"
(2,39) thick by .562" (14,27) across flats. Nuts
are brass, cadmium-plated per QQ-P-416,
Class 2, Type II.
Materials and Finishes
Military Qualified
Cover, Base and Deck Separator: Diallyl per
(MIL-M-14) ASTM-D-5948
Rotor Mounting Plate: Thermoplastic
Bushing: Zinc, cadmium-plated per QQ-P-
416, Class 2, Type II
Through Bolts and Nuts, Shaft Extension,
Lockwashers, Shaft and Rear Support
Plate, Stop Pins and Stop Arm (All
Others): Stainless steel
Detent Balls: Steel, nickel-plated
Detent Springs: Tinned music wire
Rotor Contact: Silver alloy and beryllium
copper
Base Contacts, Common Plate and Terminals:
Military Shaft and Panel Seal
A shaft and panel seal is available to provide
watertight mounting of the Series 71 standard
military style rotary switches. Sealing is
accomplished by an O-ring shaft seal and a
panel seal washer. Panel seal dimension
differences are shown in the dimensional
drawings. When the panel seal is compressed,
dimensions are approximately the same as an
unsealed switch. If the non-turn washer
supplied with the switch is used, it should not
be allowed to extend entirely through the
panel when mounting a sealed switch.
However, the bushing may be used as a non-
turn device instead. Switches are provided
with a double flat bushing in styles which
include the letter A and with a bushing which
has a keyway in the styles which include the
letter B.
Brass, gold plate .000005" minimum over
silver plate .00005" over Nickel .00002".
Detent Rotor: Phenolic per (MIL-M-14)
ASTM-D-5948
Mounting Hardware: One mounting nut and
one internal tooth lockwasher are supplied
with each Series 71 switch. For switches with
Style A in the description, the nut is .062"
(1,57) thick by .312" (7,92) across flats. For
switches with Style B or C in the description,
the nut is .094" (2,39) thick by .562" (14,27)
across flats. Nuts are brass, cadmium-plated
per QQ-P-416 Class 2, Type II.
Additional Hardware: Each switch is
supplied with a non-turn washer to use if
desired. Additionally, each PC mount switch
is supplied with a mounting bushing washer
(see PC Mount Accessory). For switches
with Style A in the description, non-turn
washer is stainless steel; for switches with
Style B in the description, non-turn washer is
stainless steel. Mounting bushing washer
(PC Mount Accessory) is brass, cadmium-
plated. For dimensions of non-turn washers
see page J-24. For custom control knobs
accessories see page I-57.