PIC16F1827-I/P Microchip Technology Inc., PIC16F1827-I/P Datasheet - Page 325

• Manufacturer Part Number: PIC16F1827-I/P
• Description: 18 PDIP .300in TUBE, 7 KB Flash, 384 bytes RAM, 32 MHz Int. Osc, 16 I/0, Enhance
• Manufacturer: Microchip Technology Inc.

Specifications of PIC16F1827-I/P

• A/d Inputs: 12-Channel, 10-Bit
• Comparators: 2
• Cpu Speed: 8 MIPS
• Eeprom Memory: 256 Bytes
• Input Output: 16
• Interface: I2C/SPI/UART/USART
• Memory Type: Flash
• Number Of Bits: 8
• Package Type: 18-pin PDIP
• Programmable Memory: 7K Bytes
• Ram Size: 384 Bytes
• Speed: 32 MHz
• Temperature Range: –40 to 125 °C
• Timers: 4-8-bit, 1-16-bit
• Voltage, Range: 1.8-5.5 V
• Standby Current (pic16lf182x): 30 nA @ 1.8 V, Typical
• Lead Free Status / Rohs Status: RoHS Compliant part

29.0
Each PIC16 instruction is a 14-bit word containing the
operation code (opcode) and all required operands.
The op codes are broken into three broad categories.
• Byte Oriented
• Bit Oriented
• Literal and Control
The literal and control category contains the most var-
ied instruction word format.
Table 29-3
MPASM
All instructions are executed within a single instruction
cycle, with the following exceptions, which may take
two or three cycles:
• Subroutine takes two cycles (CALL, CALLW)
• Returns from interrupts or subroutines take two
• Program branching takes two cycles (GOTO, BRA,
• One additional instruction cycle will be used when
One instruction cycle consists of 4 oscillator cycles; for
an oscillator frequency of 4 MHz, this gives a nominal
instruction execution rate of 1 MHz.
All instruction examples use the format ‘0xhh’ to
represent a hexadecimal number, where ‘h’ signifies a
hexadecimal digit.
 2011 Microchip Technology Inc.
cycles (RETURN, RETLW, RETFIE)
BRW, BTFSS, BTFSC, DECFSZ, INCSFZ)
any instruction references an indirect file register
and the file select register is pointing to program
memory.
TM
INSTRUCTION SET SUMMARY
assembler.
lists the instructions recognized by the
29.1
Any instruction that specifies a file register as part of
the instruction performs a Read-Modify-Write (R-M-W)
operation. The register is read, the data is modified,
and the result is stored according to either the instruc-
tion, or the destination designator ‘d’. A read operation
is performed on a register even if the instruction writes
to that register.
TABLE 29-1:
TABLE 29-2:
Field
Field
mm
DC
PC
TO
PD
W
C
b
d
n
Z
k
x
f
Register file address (0x00 to 0x7F)
Working register (accumulator)
Bit address within an 8-bit file register
Literal field, constant data or label
Don’t care location (= 0 or 1).
The assembler will generate code with x = 0.
It is the recommended form of use for
compatibility with all Microchip software tools.
Destination select; d = 0: store result in
d = 1: store result in file register f.
Default is d = 1.
FSR or INDF number. (0-1)
Pre-post increment-decrement mode
selection
Program Counter
Time-out bit
Carry bit
Digit carry bit
Zero bit
Power-down bit
PIC16(L)F1826/27
Read-Modify-Write Operations
OPCODE FIELD
DESCRIPTIONS
ABBREVIATION
DESCRIPTIONS
Description
Description
DS41391D-page 325
W
,