MAX3243EEWI+ Maxim Integrated Products, MAX3243EEWI+ Datasheet - Page 8
![IC TXRX RS-232 W/SHTDWN 28-SOIC](/photos/6/58/65865/406-28-soic_sml.jpg)
MAX3243EEWI+
Manufacturer Part Number
MAX3243EEWI+
Description
IC TXRX RS-232 W/SHTDWN 28-SOIC
Manufacturer
Maxim Integrated Products
Type
Transceiverr
Datasheet
1.MAX3221CAE.pdf
(16 pages)
Specifications of MAX3243EEWI+
Number Of Drivers/receivers
3/5
Protocol
RS232
Voltage - Supply
3 V ~ 5.5 V
Mounting Type
Surface Mount
Package / Case
28-SOIC (7.5mm Width)
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
other system to realize that the MAX3221/MAX3223/
MAX3243 is awake. If the other system outputs valid
RS-232 signals within that time, the RS-232 ports on
both systems remain enabled.
When shut down, the device’s charge pumps are turned
off, V+ decays to V
transmitter outputs are disabled (high impedance). The
time required to exit shutdown is typically 100µs (Figure
5b).
If direct software control is desired, INVALID can be
used to indicate DTR or Ring Indicator signal. Tie
FORCEOFF and FORCEON together to bypass Auto-
Shutdown so the line acts like a SHDN input.
The capacitor type used for C1–C4 is not critical for
proper operation; either polarized or nonpolarized
capacitors may be used. The charge pump requires
0.1µF capacitors for 3.3V operation. For other supply
voltages, refer to Table 3 for required capacitor values.
Do not use values smaller than those listed in Table 3.
Increasing the capacitor values (e.g., by a factor of 2)
reduces ripple on the transmitter outputs and slightly
reduces power consumption. C2, C3, and C4 can be
increased without changing C1’s value. However, do
not increase C1 without also increasing the values
of C2, C3, and C4 to maintain the proper ratios (C1
to the other capacitors).
When using the minimum required capacitor values,
make sure the capacitor value does not degrade
excessively with temperature. If in doubt, use capaci-
tors with a larger nominal value. The capacitor’s equiva-
lent series resistance (ESR) usually rises at
low temperatures and influences the amount of ripple
on V+ and V-.
1µA Supply-Current, True +3V to +5.5V
RS-232 Transceivers with AutoShutdown
Table 2. AutoShutdown Logic
8
___________Applications Information
RECEIVER INPUT
RS-232 SIGNAL
PRESENT AT
_______________________________________________________________________________________
Yes
Yes
No
No
No
Software-Controlled Shutdown
CC
F F O O R R C C E E O O F F F F INPUT
, V- decays to ground, and the
H
H
H
L
L
Capacitor Selection
FORCEON
INPUT
H
X
L
X
X
I I N N V V A A L L I I D D OUTPUT
Figure 5. AutoShutdown Trip Levels
RECEIVER
VOLTAGE
OUTPUT
INVALID
INPUT
(a)
(b)
(V)
(V)
H
H
L
L
L
V
V
+2.7V
+0.3V
-0.3V
-2.7V
CC
V+
CC
V-
0
0
0V
AUTOSHUTDOWN, TRANSMITTERS DISABLED,
TRANSMITTERS ENABLED, INVALID HIGH
TRANSMITTERS ENABLED, INVALID HIGH
1µA SUPPLY CURRENT, INVALID LOW
Normal Operation
Normal Operation (Forced On)
Shutdown (AutoShutdown)
Shutdown (Forced Off)
Shutdown (Forced Off)
t
INVL
INDETERMINATE
INDETERMINATE
TRANSCEIVER STATUS
t
INVH
INVALID
REGION
t
WU