DS26518GN+ Maxim Integrated Products, DS26518GN+ Datasheet - Page 28
![IC TXRX T1/E1/J1 8PORT 256-CSBGA](/photos/6/50/65053/256-csbga_21-0315_sml.jpg)
DS26518GN+
Manufacturer Part Number
DS26518GN+
Description
IC TXRX T1/E1/J1 8PORT 256-CSBGA
Manufacturer
Maxim Integrated Products
Type
Transceiverr
Specifications of DS26518GN+
Number Of Drivers/receivers
8/8
Protocol
T1/E1/J1
Voltage - Supply
3.135 V ~ 3.465 V
Mounting Type
Surface Mount
Package / Case
256-CSBGA
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
- Current page: 28 of 312
- Download datasheet (2Mb)
9.
9.1
Microprocessor control of the DS26518 is accomplished through the 28 hardware pins of the microprocessor port.
The 8-bit parallel data bus can be configured for Intel or Motorola modes of operation with the bus type select
(BTS) pin. When the BTS pin is a logic 0, bus timing is in Intel mode, as shown in
When the BTS pin is a logic 1, bus timing is in Motorola mode, as shown in
address space is mapped through the use of 13 address lines, A[12:0]. Multiplexed mode is not supported on the
processor interface.
The chip-select bar (CSB) pin must be brought to a logic-low level to gain read and write access to the
microprocessor port. With Intel timing selected, the read-data bar (RDB) and write-read bar (WRB) pins are used to
indicate read and write operations and latch data through the interface. With Motorola timing selected, the read-
write bar (RWB) pin is used to indicate read and write operations while the data-strobe bar (DSB) pin is used to
latch data through the interface.
The interrupt output pin (INTB) is an open-drain output that asserts a logic-low level upon a number of software
maskable interrupt conditions. This pin is normally connected to the microprocessor interrupt input.
9.1.1 SPI Serial Port Mode
The external processor bus can be configured to operate in SPI serial bus mode. See Section
timing diagrams.
When SPI_SEL = 1, SPI bus mode is implemented using four signals: clock (SPI_SCLK), master out-slave in data
(SPI_MOSI), master in-slave out data (SPI_MISO), and chip select (CSB). Clock polarity and phase can be set by
the D7/SPI_CPOL and D6/SPI_CPHA pins.
The order of the address and data bits in the serial stream is selectable using the D5/SPI_SWAP pin. The R/W bit
is always first and B bit is always last in the initial control word and are not effected by the D5/SPI_SWAP pin
setting.
SPI mode is not recommended for HDLC operations because of the bandwidth constraints of SPI.
9.1.2 SPI Functional Timing Diagrams
Note: The transmit and receive order of the address and data bits are selected by the D5/SPI_SWAP pin. The R/W
(read/write) MSB bit and B (burst) LSB bit position is not affected by the D5/SPI_SWAP pin setting.
9.1.2.1 SPI Transmission Format and CPHA Polarity
When SPI_CPHA = 0, CSB may be deasserted between accesses. An access is defined as one or two control
bytes followed by a data byte. CSB cannot be deasserted between the control bytes, or between the last control
byte and the data byte. When SPI_CPHA = 0, CSB may also remain asserted between accesses. If it remains
asserted and the BURST bit is set, no additional control bytes are expected after the first control byte(s) and data
are transferred. If the BURST bit is set, the address will be incremented for each additional byte of data transferred
until CSB is deasserted. If CSB remains asserted and the BURST bit is not set, a control byte(s) is expected
following the data byte, and the address for the next access will be received from that. Anytime CSB is deasserted,
the BURST access is terminated.
When SPI_CPHA = 1, CSB may remain asserted for more than one access without being toggled high and then
low again between accesses. If the BURST bit is set, the address should increment and no additional control bytes
are expected. If the BURST bit is not set, each data byte will be followed by the control byte(s) for the next access.
Additionally, CSB may also be deasserted between accesses when SPI_CPHA = 1. In the case, any BURST
access is terminated and the next byte received when CSB is reasserted will be a control byte.
The following diagrams describe the functionality of the SPI port for the four combinations of SPI_CPOL and
SPI_CPHA. They indicate the clock edge that samples the data and the level of the clock during no-transfer events
(high or low). Since the SPI port of the DS26518 acts as a slave device, the master device provides the clock. The
FUNCTIONAL DESCRIPTION
Processor Interface
28 of 312
Figure 13-4
Figure 13-2
and
Figure
9.1.2
and
Figure
for detailed
13-5. The
13-3.
Related parts for DS26518GN+
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![ds26518](/images/no-image3.png)
Part Number:
Description:
8-port T1/e1/j1 Transceiver
Manufacturer:
Maxim Integrated Products, Inc.
Datasheet:
![ds265188-port-t1-e1-j1-transc](/images/no-image3.png)
Part Number:
Description:
Ds26518 8-port T1/e1/j1 Transceiver
Manufacturer:
Maxim Integrated Products, Inc.
![DS26](/images/no-image3.png)
Part Number:
Description:
power light source LUXEON Collimator
Manufacturer:
LUMILEDS [Lumileds Lighting Company]
Datasheet:
![MAX7528KCWP](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
MAX7528KCWPMaxim Integrated Products [CMOS Dual 8-Bit Buffered Multiplying DACs]
Manufacturer:
Maxim Integrated Products
Datasheet:
![MAX3261CCJ](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
Single +5V, fully integrated, 1.25Gbps laser diode driver.
Manufacturer:
Maxim Integrated Products
Datasheet:
![MAX3263CAG](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
Single +5V, fully integrated, 155Mbps laser diode driver.
Manufacturer:
Maxim Integrated Products
Datasheet:
![MAX8809AETL+](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
VRD11/VRD10, K8 Rev F 2/3/4-Phase PWM Controllers with Integrated Dual MOSFET Drivers
Manufacturer:
Maxim Integrated Products
Datasheet:
![MAX1535CETJ+T](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
Highly Integrated Level 2 SMBus Battery Chargers
Manufacturer:
Maxim Integrated Products
Datasheet:
![DS2741N+](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
Current Monitor and Accumulator with Integrated Sense Resistor; ; Temperature Range: -40°C to +85°C
Manufacturer:
Maxim Integrated Products
![MAX13450EAUD+T](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
TSSOP 14/A/RS-485 Transceivers with Integrated 100O/120O Termination Resis
Manufacturer:
Maxim Integrated Products
![MAX13451EAUD+T](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
TSSOP 14/A/RS-485 Transceivers with Integrated 100O/120O Termination Resis
Manufacturer:
Maxim Integrated Products
![MAX17497BATE+](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
QFN 16/A/AC-DC and DC-DC Peak-Current-Mode Converters with Integrated Step
Manufacturer:
Maxim Integrated Products
![MAX17502FATB+T](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
TDFN/A/65V, 1A, 600KHZ, SYNCHRONOUS STEP-DOWN REGULATOR WITH INTEGRATED SWI
Manufacturer:
Maxim Integrated Products
![MAX1978EVKIT](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
Integrated Temperature Controller f
Manufacturer:
Maxim Integrated Products