LTC1485CS8 Linear Technology, LTC1485CS8 Datasheet
![IC TXRX DIFFERNTIAL BUS 8-SOIC](/photos/6/62/66297/8-soic_05-08-1610_sml.jpg)
LTC1485CS8
Specifications of LTC1485CS8
Available stocks
Related parts for LTC1485CS8
LTC1485CS8 Summary of contents
Page 1
... ESD strikes of over 10kV. The receiver has a fail-safe feature which guarantees a high output state when the inputs are left open. Both AC and DC specifications are guaranteed from – and 4.75V to 5.25V supply voltage range. , LTC and LT are registered trademarks of Linear Technology Corporation LTC1485 6 ...
Page 2
... Low ORDER PART TOP VIEW NUMBER LTC1485CN8 LTC1485IN8 GND LTC1485CS8 LTC1485IS8 S8 PACKAGE 8-LEAD PLASTIC SOIC S8 PART MARKING = 125 C, = 100 150 C, = 150 C/ W (S) JA 1485 1485I MIN TYP MAX 1.5 5 0.2 3 0.2 2.0 0.8 = 12V 1.0 = – 7V – 0.8 – 0.2 ...
Page 3
U S WITCHI G C HARA TERISTICS (Notes 2, 3), unless otherwise noted. CC SYMBOL PARAMETER t Driver Input to Output PLH t Driver Input to Output PHL t Driver Output to Output SKEW t , ...
Page 4
LTC1485 W U TYPICAL PERFOR A Receiver Output Low Voltage vs Temperature 0 8mA 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0 –50 – 100 125 TEMPERATURE ( C) 1485 G04 Driver Output ...
Page 5
CTIO S RO (Pin 1): Receiver Output. If the receiver output is enabled (RE low), then if A > 200mV, RO will be high < 200mV, then RO will ...
Page 6
LTC1485 WITCHI WAVEFOR – 10% – A A OD2 ...
Page 7
WITCHI TI E WAVEFOR PPLICATI S I FOR ATIO Typical Application A typical connection of the LTC1485 is shown in Figure ...
Page 8
LTC1485 PPLICATI S I FOR ATIO Thermal Shutdown The LTC1485 has a thermal shutdown feature which protects the part from excessive power dissipation. If the outputs of the driver are accidentally shorted to a power supply ...
Page 9
PPLICATI S I FOR ATIO PROBE HERE R DX DRIVER 120 470 Figure 12. Termination Effects AC Cable Termination Cable termination resistors are necessary to prevent un- wanted ...
Page 10
LTC1485 PPLICATI S I FOR ATIO The termination resistors are used to generate a DC bias which forces the receiver output to a known state, in this case a logic 0. The first method consumes about ...
Page 11
... MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.010 INCH (0.254mm). Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no represen- tation that the interconnection of circuits as described herein will not infringe on existing patent rights. ...
Page 12
... Fits 75179 Pinout, Only 300 A I Fits 75176 Pinout 499-3977 0.189 – 0.197* (4.801 – 5.004 0.150 – 0.157* (3.810 – 3.988 0.004 – 0.010 (0.101 – 0.254) 0.050 (1.270) BSC SO8 0294 sn1485 1485fs LT/GP 0795 2K REV A • PRINTED IN THE LINEAR TECHNOLOGY CORPORATION 1995 USA ...