3G3JX-A2037 Omron Automation, 3G3JX-A2037 Datasheet - Page 53
![no-image](/images/no-image-200.jpg)
3G3JX-A2037
Manufacturer Part Number
3G3JX-A2037
Description
Drive, Adjustable Frequency, 3-Phase, 240VAC, 5.0HP, 15.9A, RS-485 Serial , IP20
Manufacturer
Omron Automation
Type
Adjustable Frequencyr
Datasheet
1.3G3JX-A2004.pdf
(57 pages)
Specifications of 3G3JX-A2037
Brand/series
JX
Current, Input
20 A
Function
Motor Control
Horse Power Rating
5 HP
Mounting Type
Screw
Phase
Three
Power Rating
5.0 HP
Primary Type
AC Drive
Standards
IP20
Voltage, Supply
240 VAC
Voltage, Supply Maximum
240
Lead Free Status / Rohs Status
RoHS Compliant part
■ Detailed Method for Braking Resistor
If the Braking Resistor's use rate (duty factor) exceeds 10% ED
or the application requires an extremely large braking torque,
use the following method to calculate the regenerative energy
and select a Braking Resistor.
● Calculating the Required Braking Resistance
* Use the value for the braking torque calculated in Calculating the Motor Shaft
● Calculating the Average Regenerative Energy
Regenerative energy is produced when the motor is rotating in
the opposite direction of the motor torque. Use the following
equations to calculate the regenerative energy produced in each
segment of the cycle.
Note 1. The speed is positive when the motor is rotating forward and the torque
Conversion Torque and Effective Torque on page 58.
Speed
Speed
Torque
Torque
Selection
2. Use the value for the braking torque calculated in Calculating the Motor
is positive when it is in the forward direction.
Shaft Conversion Torque and Effective Torque on page 58.
Segment 1
Braking Resistor’s resistance: R ≤
Speed
Torque
V: 385 V for a 200-V Class Inverter
T: Maximum braking torque (kgf
Tm: Motor’s rated torque (N
N: Maximum speed (r/min)
Horizontal load
Vertical load
400 V for a 400-V Class Inverter
Segment 2
Segment 1
Time
Segment 2
Segment 3
Time
Time
Calculate the average regenerative energy by
adding the power produced in each segment
of the cycle and dividing by the total cycle time.
Average regenerative energy (W) =
Energy at max. speed N (r/min):
The kinetic energy is proportional
to the square of the speed, so the
regenerative energy is highest
momentarily at this point.
Max deceleration torque T (kgf
Regenerative energy is produced
when the motor's direction is
opposite the motor torque direction.
•
cm)
Pi: N x T x t x 1.048 x 10
Pi: Regenerative energy (J) produced in segmenti
N: Motor’s speed (r/min)
T: Deceleration torque (N•m)
t: Deceleration time (s)
1.048 x (T-0.2 x Tm) x N x 10
(Use the average speed if the speed varies.)
•
cm)
V
2
-1
•
cm):
(P1 + P2 + ...... + P)
1 cycle time
-1
● Selecting the Braking Resistor
Select the appropriate Braking Resistor based on the required
braking resistance and average regenerative energy that were
calculated above.
Note 1. The internal braking transistor will be damaged if a resistor is connected
• Required braking resistance ≥ Braking Resistor Unit's resis-
• Average regenerative energy ≤ Braking Resistor Unit's allow-
tance ≥ Inverter or Braking Unit's minimum resistance
able power
2. Two or more Braking Units can be connected in parallel. Use the follow-
3. Do not select the braking resistance with the results calculated above.
with a resistance below the Inverter or Braking Unit's minimum resis-
tance. If the required resistance is less than the minimum resistance, in-
crease the Inverter's capacity and replace the Inverter or Braking Unit
with one that has a minimum resistance less than the required resis-
tance.
ing equation to determine the braking resistance when driving two or
more Units.
Braking resistance (Ω) = (required braking resistance calculated above)
× (number of Units)
A rating of 150 W is not the allowed power, it is the maximum rated pow-
er in resistance units. The actual allowed power rating depends upon
the resistor.
Overview of Inverter Selection
Overview of Inverter Selection
61