DP-190 200ML 3M, DP-190 200ML Datasheet - Page 7
![no-image](/images/manufacturer_photos/0/0/1/3m_sml.jpg)
DP-190 200ML
Manufacturer Part Number
DP-190 200ML
Description
Adhesive; Epoxy; Gray
Manufacturer
3M
Datasheet
1.DP-190_200ML.pdf
(8 pages)
Specifications of DP-190 200ML
Chemical Component
Epoxy Resin/Kaolin
Chemical System
Epoxy
Color
Gray
Dispensing Method
Syringe
Primary Type
Adhesive
Special Features
High Strength
Time, Drying
Air Dry for 15 minutes, Force Dry for 10 minutes @ 65 °C (Aluminum Surface), If 3M™ Scotch-Weld™ Structural Adhesive Primer EC1945 B⁄A is Used, Apply a Thin Coating (0.5 mils) on the Metal Surfaces to be Bonded, Air Dry for 10 minutes, then Cure for 30 mi
Time, Setting
15 min. (Aluminum), 10 min. (Steel)
Weight
200 ml
Select and use gloves and/or protective clothing to prevent skin contact based on the results of an exposure assessment. Consult with
your glove and/or protective clothing manufacturer for selection of appropriate compatible materials.
Gloves made from the following material(s) are recommended: Polyethylene/Ethylene Vinyl Alcohol.
8.2.3 Respiratory Protection
Avoid breathing of dust created by cutting, sanding, grinding or machining.
Select one of the following NIOSH approved respirators based on airborne concentration of contaminants and in accordance with
OSHA regulations: Half facepiece or fullface air-purifying respirator with P100 particulate filters, Half facepiece or fullface air-
purifying respirator with P95 particulate filters, Half facepiece or fullface air-purifying respirator with N95 particulate filters.
Consult the current 3M Respiratory Selection Guide for additional information or call 1-800-243-4630 for 3M technical assistance.
8.2.4 Prevention of Swallowing
Do not eat, drink or smoke when using this product. Wash exposed areas thoroughly with soap and water.
8.3 EXPOSURE GUIDELINES
regulatory agency.
SOURCE OF EXPOSURE LIMIT DATA:
_________________________________________________________________________________________________
VAC Vacated PEL:Vacated Permissible Exposure Limits [PEL] are enforced as the OSHA PEL in some states. Check with your local
3M MATERIAL SAFETY DATA SHEET 3M(TM) Scotch-Weld(TM) Epoxy Adhesive DP-190, Gray (Part B)
KAOLIN
KAOLIN
KAOLIN
KAOLIN
Ingredient
SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES
ACGIH: American Conference of Governmental Industrial Hygienists
CMRG: Chemical Manufacturer Recommended Guideline
OSHA: Occupational Safety and Health Administration
AIHA: American Industrial Hygiene Association Workplace Environmental Exposure Level (WEEL)
Specific Physical Form:
Odor, Color, Grade:
General Physical Form:
Autoignition temperature
Flash Point
Flammable Limits - LEL
Flammable Limits - UEL
Boiling point
Density
Vapor Density
Vapor Pressure
Specific Gravity
pH
Melting point
Solubility in Water
Evaporation rate
Volatile Organic Compounds
ACGIH
OSHA
OSHA
OSHA
Authority
dust
TWA, respirable
TWA, respirable
TWA, Vacated, as
TWA, as total dust
Type
Viscous
white cream, very slight odor
Liquid
>=248 ºC [Test Method: Pensky-Martens Closed Cup]
1.33 g/ml
<=0.1 mmHg [@ 25 ºC]
1.33 [Ref Std: WATER=1]
Nil
0.8 g/l [Test Method: tested per EPA method 24]
Not Applicable
Not Applicable
Not Applicable
Not Applicable
Not Applicable
Not Applicable
Not Applicable
Not Applicable
2 mg/m3
5 mg/m3
10 mg/m3
15 mg/m3
Limit
Table A4
Table Z-1
Table Z-1
Additional Information
Page
4 of 7