LTC491CS Linear Technology, LTC491CS Datasheet - Page 8
![IC TXRX RS485 LOW POWER 14-SOIC](/photos/6/87/68753/14-soic_05-08-1610_sml.jpg)
LTC491CS
Manufacturer Part Number
LTC491CS
Description
IC TXRX RS485 LOW POWER 14-SOIC
Manufacturer
Linear Technology
Type
Transceiverr
Datasheet
1.LTC491CNPBF.pdf
(12 pages)
Specifications of LTC491CS
Number Of Drivers/receivers
1/1
Protocol
RS422, RS485
Voltage - Supply
4.75 V ~ 5.25 V
Mounting Type
Surface Mount
Package / Case
14-SOIC (3.9mm Width), 14-SOL
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
LTC491CS
Manufacturer:
LINEAR/凌特
Quantity:
20 000
Company:
Part Number:
LTC491CS#PBF
Manufacturer:
LT
Quantity:
4 560
Company:
Part Number:
LTC491CS#PBF
Manufacturer:
LTC
Quantity:
813
Part Number:
LTC491CS#TR
Manufacturer:
LT/凌特
Quantity:
20 000
Company:
Part Number:
LTC491CS#TRPBF
Manufacturer:
TI
Quantity:
1 500
A
Cables and Data Rate
The transmission line of choice for RS485 applications is
a twisted pair. There are coaxial cables (twinaxial) made
for this purpose that contain straight pairs, but these are
less flexible, more bulky, and more costly than twisted
pairs. Many cable manufacturers offer a broad range of
120 cables designed for RS485 applications.
Losses in a transmission line are a complex combination
of DC conductor loss, AC losses (skin effect), leakage and
AC losses in the dielectric. In good polyethylene cables
such as the Belden 9841, the conductor losses and
dielectric losses are of the same order of magnitude,
leading to relatively low over all loss (Figure 11).
LTC491
8
PPLICATI
Figure 11. Attenuation vs Frequency for Belden 9481
10k
100
1.0
0.1
10
10
1k
Figure 12. Cable Length vs Data Rate
0.1
10k
O
U
100k
FREQUENCY (MH
1.0
S
DATA RATE (bps)
I FOR ATIO
U
1M
10
Z
)
2.5M
W
LTC491 • F11
LTC491 • F12
10M
100
U
When using low loss cables, Figure 12 can be used as a
guideline for choosing the maximum line length for a given
data rate. With lower quality PVC cables, the dielectric loss
factor can be 1000 times worse. PVC twisted pairs have
terrible losses at high data rates (>100kBs), and greatly
reduce the maximum cable length. At low data rates
however, they are acceptable and much more economical.
Cable Termination
The proper termination of the cable is very important.
If the cable is not terminated with it’s characteristic
impedance, distorted waveforms will result. In severe
cases, distorted (false) data and nulls will occur. A quick
look at the output of the driver will tell how well the cable
is terminated. It is best to look at a driver connected to the
end of the cable, since this eliminates the possibility of
getting reflections from two directions. Simply look at the
driver output while transmitting square wave data. If the
cable is terminated properly, the waveform will look like a
square wave (Figure 13).
If the cable is loaded excessively (47 ), the signal initially
sees the surge impedance of the cable and jumps to an
initial amplitude. The signal travels down the cable and is
reflected back out of phase because of the mistermination.
Rt = 120
Rt = 470
Rt = 47
DX
DRIVER
Figure 13. Termination Effects
PROBE HERE
Rt
RECEIVER
LTC491 • F13
RX
491fa