TBCR Bogen Communications, Inc., TBCR Datasheet

TBCR

Manufacturer Part Number

TBCR

Description

Tile Bridge Support FOR HSCF

Manufacturer

Bogen Communications, Inc.

Datasheet

1.TBCR.pdf (2 pages)

Specifications of TBCR

Dimensions

17"(W) × 11⁄8"(H) × 24"(D)

Mounting Type

Flush

Lead Free Status / Rohs Status

RoHS Compliant part

For Use With

Speaker

Current page: 1 of 2
Download datasheet (227Kb)

Model TBCR

TILE BRIDGE SUPPORT RING

Description

Installation

SUSPENDED CEILING INSTALLATION

NEW CONSTRUCTION - JOISTS EXPOSED

The Tile Bridge Support Ring (TBCR) is designed to offer additional

mounting support for a variety of installations involving clamping type

ceiling speakers.

1. Remove the tile from the ceiling and put the TBCR on top of the ceil-

In new constructions, the TBCR can serve as a routing guide for the

speaker cutout when installed before the sheetrock is applied. It provides

a second benefit by stiffening the area around the bezel after speaker

installation.

A. For 16" Centers Joist Spacing

1. Remove the 4 breakaway tabs.

ing tile, aligning the ends of the TBCR rails as shown in the drawing.

Typically the ceiling speaker will be mounted in the center of the

ceiling tile.The support ring should be positioned in the center of the

rails and the ends of the rails flush with the sides of the tile for this

installation. The speaker can be mounted in other locations in the

ceiling tile by moving the ring and/or tile bridge assembly if desired,

however, care must be taken to ensure that the TBCR rails will still

be flush with the tile sides and that the ring portion will not

interfere with the suspension grid.

Use the ring as a guide to cut a hole in the ceiling tile.

Sandwich the tile between the TBCR and the speaker bezel and

tighten the speaker clamps. Complete speaker installation and

connections as directed in speaker’s instruction manual.

In 16" joist spaces (the outside distance of the joists must be no

greater than 17" and the inside spacing of the joists must be no less

than 14¾" in order for the rails to fit), the support ring must remain

in the center of the rails. Shifting the ring position may cause the

swing out clamps of the speaker to hit the joist and prevent it from

fully extending.

Note: Support Ring must be fully within the joist space for

the speaker to mount correctly. Also, check that there is

sufficient vertical space above the ring to fit the particular

speaker being used.

With the ring section attached, nail the TBCR in 4 places to the

bottom of the joists through the nail holes. (Two nail holes are

provided in each joist location. Pick the one that is closest to the joist

center.) The 24" center tails of the rails will protrude into the

adjacent joist spaces.

After the sheetrock is up and the hole routed, follow the speaker’s

installation instructions to complete the installation.

Related parts for TBCR

TBCR Summary of contents

Page 1

... Installation SUSPENDED CEILING INSTALLATION 1. Remove the tile from the ceiling and put the TBCR on top of the ceil- ing tile, aligning the ends of the TBCR rails as shown in the drawing. 2. Typically the ceiling speaker will be mounted in the center of the ceiling tile ...

Page 2

... The TBCR is warranted to be free from defects in material or workmanship for five (5) years from the date of sale to the original purchaser.Any part of the prod- uct covered by this warranty that, with normal installation and use, becomes defective will be repaired or replaced by Bogen, at our option, provided the product is shipped insured and prepaid to: Bogen Factory Service Department, 50 Spring Street, Ramsey, NJ 07446, USA ...

Related keywords

TBCR datasheet
TBCR data sheet
TBCR pdf datasheet
TBCR component
TBCR part
TBCR distributor
TBCR RoHS
TBCR datasheet download