HE9Z-D3Y IDEC Corporation, HE9Z-D3Y Datasheet - Page 4
![no-image](/images/no-image-200.jpg)
HE9Z-D3Y
Manufacturer Part Number
HE9Z-D3Y
Description
Cover; Yellow; Rubber; UL Recognized, CSA Certified
Manufacturer
IDEC Corporation
Datasheet
1.HE9Z-D3Y.pdf
(5 pages)
Specifications of HE9Z-D3Y
Color
Yellow
Material, Body
Rubber
Standards
UL Recognized, CSA Certified
Lead Free Status / Rohs Status
RoHS Compliant part
• In order to avoid electric shock or fire, turn power off before installa-
• Follow specification when installing. Improper electrical load may
HE2B
• M3 nut is inside the rubber cover.
HE2B/HE3B
• A change in internal air pressure may cause the rubber boot to
HE1B/HE2B/HE3B
• Applicable wire size is 0.5mm (maximum) / 1 line.
• When soldering the terminal, solder at a temperature of 260°C within
HE1G
• Wire Striping Information
HE2B/HE3B/HE1G
• To ensure the highest level of reliability connect both contacts to a
www.idec.com
• Applicable Wire Size:0.14 to 1.5mm
Wire Length
L1, L2 (mm)
L3 (mm)
tion, removal, wire connection, maintenance or inspection of
switch.
damage switch, cause electric shock, or fire.
expand and shrink on an enabling switch that has the rubber boot
sealed. This may affect the performance of the switch. Periodically
check to ensure that the enabling switch is operating correctly.
3 seconds. Use non-corrosive liquid rosin as soldering flux.
monitoring device such as a safety relay.
Mounting Screw
Safety Products
L1=40mm
L3=6mm
Terminal No. 1-4
Terminal No.
Grip Switch
Nut
2
(one wire per terminal)
USA: (800) 262-IDEC or (408) 747-0550, Canada (888) 317-IDEC
General Information for Enabling Switches
L2=27mm
Terminal No. 5-8
Installation Precautions
Wiring Precautions
Safety Precautions
Use Precautions
• Use proper wire diameter to meet voltage and current requirements.
• If the panel is not level when mounting an enabling switch, the
HE3B
• The rubber boot has a tab to be used for orientation. When making a
• When tightening the locking ring, secure the flange to prevent the
• Recommended Torque (wire diameter range.276 - .512”)
HE1B/HE2B/HE3B
• When installing the enabling switch ensure that it cannot be acci-
Case Installation
Rubber Installation
Connector
Strain Relief
Wire terminals
Do Not Remove
Using improper wires or incomplete soldering may cause fire due to
abnormal heat generation.
waterproof feature cannot be guaranteed.
positioning hole in a panel, do not make a hole in the rubber boot, or
the waterproof feature cannot be guaranteed. When the positioning
hole in not on the panel, remove the tab, but do not make a hole in
the rubber boot.
enabling switch from rotating. In applications where the enabling
switch is to be rotated, mount the switch in a recess on the panel as
shown.
dently activated. For example, a protrusion from a teaching pendant
could cause the enabling switch to be activated by the weight of the
teaching pendant.
The above values apply when using IDEC strain relief.
If using other, contact manufacturer.
cover
cover
base
base
See Drawing Above
B
F
A
B
C
D
E
F
E
C
base
D
A (M4 screw x 3)
General Information
Recommended Torque
1.2±0.1N • m
.09±0.1N • m
3.0±0.3N • m
6.0±0.3N • m
0.3±0.2N • m
–
B-51
B