594D686X9010C2T Sprague / Vishay, 594D686X9010C2T Datasheet - Page 9

• Manufacturer Part Number: 594D686X9010C2T
• Description: Capacitor; Tantalum; Cap 68 uF; Tol 10%; Vol-Rtg 10 VDC; SMT; 0.1 Ohms
• Manufacturer: Sprague / Vishay

Specifications of 594D686X9010C2T

• Capacitance: 68 μF
• Case Code: C
• Esr: 0.1 Ohms
• Material, Element: Tantalum
• Termination: SMT
• Tolerance: ±10 %
• Voltage, Rating: 10 VDC
• Terminations: 100% Tin (2) Standard
• Capacitance Range: 1 μF to 1500 μF
• Lead Free Status / Rohs Status: RoHS Compliant part

594D
Vishay Sprague
www.vishay.com
74
Note: Metric dimensions will govern. Dimensions in inches are rounded and for reference only.
Notes:
1. A
2. Tape with components shall pass around radius "R" without damage. The minimum trailer length may require additional length to
3. This dimension is the flat area from the edge of the sprocket hole to either the outward deformation of the carrier tape between the
4. This dimension is the flat area from the edge of the carrier tape opposite the sprocket holes to either the outward deformation of the
5. The embossment hole location shall be measured from the sprocket hole controlling the location of the embossment. Dimensions of
6. B
Concentric around B
TAPE AND REEL PACKAGING in inches [millimeters]
B
Double Pitch
For Tape Feeder
including draft.
Reference only
0
dimensions of the component. The clearance between the ends of the terminals or body of the component to the sides and depth of
the cavity (A
rotation of the component within the cavity of not more than 20 degrees.
provide R minimum for 12mm embossed tape for reels with hub diameters approaching N minimum.
embossed cavities or to the edge of the cavity whichever is less.
carrier tape between the embossed cavity or to the edge of the cavity whichever is less.
embossment location and hole location shall be applied independent of each other.
(Note 6)
B
.024 [0.600]
(Top View)
0
1
1
12mm
12mm
TAPE
B
Max.
(Note 5)
SIZE
dimension is a reference dimension for tape feeder clearance only.
0
Max.
K
A
0
0
are determined by the maximum dimensions to the ends of the terminals extending from the component body and/or the body
Component Rotation
20
Max.
Component
0
Center Line
.004 [0.10]
B
Component
Center Line
T
°
0
Typical
2
Cavity
0
Maximum
Max.
Typical
K
B
0
(Note 6)
) must be within 0.002" [0.05mm] minimum and 0.020" [0.50mm] maximum. The clearance allowed must also prevent
1
0.323
0.323
[8.2]
[8.2]
(Max.)
K
0
Cover
Tape
Top
Embossments
D
(Note 5)
Deformation
Allowable Camber to be .039/3.937 [1/100]
Cover
1
0.059
0.059
Tape
Between
[1.5]
[1.5]
Top
(Min.)
Non-Cumulative Over 9.843 [250.0]
3.937 [100.0]
Center Lines
of Cavity
For technical questions, contact [e-mail]
.039 [1.0]
Max.
.059 + .004 - 0.0
[1.5 + 0.10 - 0.0]
9.843 [250.0]
0.217 ± 0.002
0.453 ± 0.004
[11.5 ± 0.03]
(Top View)
[5.5 ± 0.05]
Camber
USER DIRECTION OF FEED
F
.039 [1.0] Max.
A
0
Tape
P
B
1
0
[4.0
.157
0.157 ± 0.004
0.315 ± 0.004
[4.0 ± 0.1]
[8.0 ± 0.1]
±
±
0.10]
.004
P
DIRECTION OF FEED
1
Maximum Cavity
Cathode (-)
Size (Note 1)
[2.0
.079
10 Pitches Cumulative
Tolerance on Tape
±
Tape and Reel Specifications: All case codes are available
on plastic embossed tape per EIA-481-1. Tape reeling per
IEC 286-3 is also available. Standard reel diameter is 7"
[178mm]. 13" [330mm] reels are available and recommended
as the most cost effective packaging method.
The most efficient packaging quantities are full reel increments
on a given reel diameter. The quantities shown allow for the
sealed empty pockets required to be in conformance with
EIA-481-1. Reel size and packaging orientation must be
specified in the Vishay Sprague part number.
0.008 [0.2]
Anode (+)
±
±
0.05]
.002
R (Min.)
(Note 2)
.079 x .047 [2.0 x 1.2] and Larger.
1.181
[30.0]
1.181
[30.0]
Embossment
Min. (Note 3)
D
.030 [0.75]
Min. (Note 4)
1
.030 [0.75]
Min. For Components
(Note 5)
[1.75
.069
(Max.)
0.256
0.256
[6.5]
[6.5]
T
F
±
±
2
.004
0.10]
W
0.472 ± 0.012
0.945 ± 0.012
[12.0 ± 0.30]
[24.0 ± 0.03]
W
Document Number 40006
(Side or Front Sectional View)
20
Component
°
Maximum
Rotation
Revision 09-Mar-05
(Note 1)
A
0
B
0
K
0