F35-3-14-0 Simpson, F35-3-14-0 Datasheet

F35-3-14-0

Manufacturer Part Number

F35-3-14-0

Description

Panel Meter, Digital, 3 1/2 digits, 120 VAC Supply, Range 200 DCV

Manufacturer

Simpson

Type

Voltager

Datasheet

1.F35-3-14-0.pdf (3 pages)

Specifications of F35-3-14-0

Accuracy

±0.1% %

Connection Type

Screw

Cut Out, Panel

1/8 DIN

Dimensions

3.78"L×2.94"D×1.89"H

Display Digit Height

0.56 "

Display Resolution

100 mV

Display Type

LED

Function

Voltage

Material, Casing

Noryl

Number Of Digits

3-1/2

Primary Type

Electronic

Range, Measurement

200 VDC

Voltage, Supply

9 to 32 VDC

Current page: 1 of 3
Download datasheet (322Kb)

The Falcon Series digital indicators are premium quality

1/8 DIN meters for industrial applications. All Falcon units

feature jumper selectable decimal point (internal and on the

connector for remote decimal point) and display scaling,

providing wide application flexibility. In addition, signal input

ranges are easy to change with jumpers on the main board.

The Falcon has a 0.56" bright red LED display for high vis-

ibility.

Full 3-1/2 Digit, Bright Red 0.56" (14.2mm) Display

Broad Range Display Scaling

Short 2.94" (74.7mm) Deep, 1/8 DIN Case

Screw Terminal Connector for Easy Installation

Four User-Settable Ranges: 200mV, 2V, 20V, 200V

One Factory-Settable Range: 750V

Jumper-Selectable Decimal Point

Optional Isolated 9-32VDC Power Supply

Optional Excitation Output of 12VDC or 24VDC

Installation and Panel Cutout

102.5mm

91.2mm

4.04"

3.59"

96mm

3.78"

48mm

1.89"

11.2mm

0.44"

45mm

1.77"

74.7mm

2.94"

91.9mm

3.62"

44.2mm 2.22"

1.74"

Falcon F35 Series Digital Panel Meter

56.5mm

Mounting Requirements

The Falcon series 1/8 DIN indicators require a panel cutout of 1.77"

(45mm) high by 3.62" (92mm) wide. To install the Falcon into a panel cut-

out, remove the clips from the side of the meter. Slide the meter through

your panel cutout, then slide the mounting clips back on the meter. Press

evenly to ensure a proper fit.

Engineering Label Placement

If replacement of the engineering unit label is required, place the tip of a

ball-point pen into the small hole at the base of the engineering label in

the bezel. Slide the label up until it pops out. Grasp and remove. Slide

the new label half the distance in, then use the ball-point pen to slide it

down into place.

Compactly designed for applications requiring minimal rear

panel depth, the Falcon fits a standard 1/8 DIN panel cutout

(92mm x 45mm) and requires less than 3" behind the panel.

A screw terminal connector is a standard feature for easy

wiring of the power supply and signal input connections.

DC Voltage

Engineering Label

Related parts for F35-3-14-0

F35-3-14-0 Summary of contents

Page 1

... Falcon F35 Series Digital Panel Meter Compactly designed for applications requiring minimal rear panel depth, the Falcon fits a standard 1/8 DIN panel cutout (92mm x 45mm) and requires less than 3" behind the panel. A screw terminal connector is a standard feature for easy wiring of the power supply and signal input connections. 3.62" ...

Page 2

... 200V 750 volt range may be configured by factory or Simpson Authorized Service Center only. ENVIRONMENTAL Operating Temperature 55ºC Storage Temperature: -10 to 60ºC Relative Humidity 85% non-condensing Temperature Coefficient: (±0.01% of input ± 0.05 count)/ºC Warm-up Time: Less than 15 minutes Response Time: Less than 1 second ...

Page 3

... The Falcon is less than 3" deep, fitting well into the restricted panel space. It will take up about as much space as the analog meter it replaced. In addition, display hold is a stan- Ordering Information F35 Basic Unit Power Supply F35 3-1/2 Digit Indicator 1 120VAC 2 ...

Related keywords

F35-3-14-0 datasheet
F35-3-14-0 data sheet
F35-3-14-0 pdf datasheet
F35-3-14-0 component
F35-3-14-0 part
F35-3-14-0 distributor
F35-3-14-0 RoHS
F35-3-14-0 datasheet download