ARJ210-M5 SMC Corporation, ARJ210-M5 Datasheet - Page 4

• Manufacturer Part Number: ARJ210-M5
• Description: REGULATOR, MINI
• Manufacturer: SMC Corporation

Specifications of ARJ210-M5

• Pressure, Operating: 1 MPa (Max.)
• Proof Pressure: 1.5 MPa
• Size, Port: M5 × 0.8
• Temperature, Ambient: -5 to +60 °C
• Operating Pressure: 150 psi (Adjustment Range
• Lead Free Status / Rohs Status: RoHS Exempt Product

Component Parts
Dimensions
Construction/Dimensions
Manifold Base (Option)/Dimensions
No. Description
q
w
e
r
t
y
u
!0
ARJ1020F-M5-04
ARJ1020F-M5-06
Body
Valve guide
Piston
Bonnet
Handle
Adjusting spring
Valve
Nipple
Model
IN (Common)
Applicable tubing O.D. C
Polyacetal
Steel wire
Material
21
22
Brass
Brass
Brass
Brass
Brass
A
Panel screw
PBT
Lock nut
M8 X 0.75
10.4
12.8
(Mounting hole)
B
Electroless nickel plated
Electroless nickel plated
Electroless nickel plated
Electroless nickel plated
Zinc chromated
Rubber lining
2-ø3.5
(Mounting
hole)
C
4
6
Note
M5 x 0.8
D
base part no.
ARJM10-4
ARJM10-6
ARJM10-10
Manifold
Replacement Parts
∗ When replacing valves and springs, remove
E
6
No. Description
u
i
o
nipple first. Note that adhesive is applied to
the nipple portion.
(Width across
Valve
Gasket
Spring
flats: 10)
10.6
F
Stations
Miniature Regulator
10
4
6
Stainless steel
Stainless steel
Brass, HNBR
Applicable tubing
O.D. ø4, ø6
Panel mounting hole
Material
3.5
G
A dimension
NBR
130
210
90
MAX. 2.5t
15.5
H
P233014-04
13434-30
B dimension
Part no.
134313
50
J
122
202
82
17.2
K
Series
1. To connect the IN side, hold the valve
2. While piping to products or operating
1.
1. Release the lock to adjust the pressure.
2. This product cannot be used as a
Be sure to read before handling.
Refer to pages 14-21-3 to 14-21-4
for
Common Precautions.
guide at its wrench flats (opposite side
10) and tighten it at the recommended
torque of 1.5 to 2 N·m.
Excessive torque or holding it at an
area other than the specified portion
may result in a malfunction.
the handle, ensure that an excess
bending moment should not be applied
to a product, because it may result in
damage.
Set up the regulator while verifying the
pressure that is indicated on the inlet
and the outlet pressure gauges. Turning
the handle excessively could damage
the internal parts.
After the adjustment, engage the lock.
Failure to observe this procedure could
damage the handle or cause the outlet
pressure to fluctuate.
<Lock operating method>
Loosen the lock nut to unlock it, and
tighten it to lock it.
check regulator by installing it between
solenoid valve and actuator.
Warning
Warning
Caution
Mounting/Adjustment
Safety
Precautions
ARJ1020F
Piping
Instructions
14-4-5
and
F.R.L.
AV
AU
AF
AR
IR
VEX
AMR
ITV
IC
VBA
VE„
VY1
G
PPA
AL