MAX3095ESE+ Maxim Integrated Products, MAX3095ESE+ Datasheet - Page 8

• Manufacturer Part Number: MAX3095ESE+
• Description: IC RS485/422 RX 10MBPS 16-SOIC
• Manufacturer: Maxim Integrated Products
• Type: Receiverr

Specifications of MAX3095ESE+

• Number Of Drivers/receivers: 0/4
• Protocol: RS422, RS485
• Voltage - Supply: 4.75 V ~ 5.25 V
• Mounting Type: Surface Mount
• Package / Case: 16-SOIC (3.9mm Width)
• Data Rate: 10 Mbps
• Operating Supply Voltage: 5 V
• Supply Current: 2.4 mA
• Operating Temperature Range: - 40 C to + 85 C
• Maximum Power Dissipation: 696 mW
• Mounting Style: SMD/SMT
• Ic Interface Type: RS422, RS485
• Supply Voltage Range: 4.75V To 5.25V
• Driver Case Style: SOIC
• No. Of Pins: 16
• Filter Terminals: SMD
• Rohs Compliant: Yes
• Data Rate Max: 10Mbps
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

As with all Maxim devices, ESD-protection structures
are incorporated on all pins to protect against electro-
static discharges (ESD) encountered during handling
and assembly. The MAX3095/MAX3096 receiver inputs
have extra protection against static electricity found in
normal operation. Maxim’s engineers developed state-
of-the-art structures to protect these pins against ±15kV
ESD, without damage. After an ESD event, the MAX3095/
MAX3096 continue working without latchup.
ESD protection can be tested in several ways. The
receiver inputs are characterized for protection to the
following:
1) ±15kV using the Human Body Model
2) ±8kV using the Contact-Discharge Method specified
3) ±15kV using the Air-Gap Method specified in
ESD performance depends on a number of conditions.
Contact Maxim for a reliability report that documents
test setup, methodology, and results.
Figure 4a shows the Human Body Model, and Figure
4b shows the current waveform it generates when dis-
charged into a low impedance. This model consists of a
100pF capacitor charged to the ESD voltage of interest,
which is then discharged into the device through a
1.5kΩ resistor.
Since January 1996, all equipment manufactured and/or
sold in the European community has been required to
meet the stringent IEC 1000-4-2 specification. The IEC
1000-4-2 standard covers ESD testing and performance
of finished equipment; it does not specifically refer to inte-
grated circuits. The MAX3095/MAX3096 help you design
equipment that meets Level 4 (the highest level) of IEC
1000-4-2, without additional ESD-protection components.
±15kV ESD-Protected, 10Mbps, 3V/5V,
Quad RS-422/RS-485 Receivers
8
_______________Detailed Description
in IEC 1000-4-2 (formerly IEC 801-2)
IEC 1000-4-2 (formerly IEC 801-2)
_______________________________________________________________________________________
±15kV ESD Protection
ESD Test Conditions
Human Body Model
IEC 1000-4-2
The main difference between tests done using the
Human Body Model and IEC 1000-4-2 is higher peak
current in IEC 1000-4-2. Because series resistance is
lower in the IEC 1000-4-2 ESD test model (Figure 5a), the
ESD-withstand voltage measured to this standard is gen-
erally lower than that measured using the Human Body
Model. Figure 5b shows the current waveform for the
±8kV IEC 1000-4-2 Level 4 ESD Contact-Discharge test.
The Air-Gap test involves approaching the device with a
charge probe. The Contact-Discharge method connects
the probe to the device before the probe is energized.
The Machine Model for ESD testing uses a 200pF stor-
age capacitor and zero-discharge resistance. It mimics
the stress caused by handling during manufacturing
and assembly. Of course, all pins (not just RS-485
inputs) require this protection during manufacturing.
Therefore, the Machine Model is less relevant to the I/O
ports than are the Human Body Model and IEC 1000-4-2.
Table 1 shows the functionality of the enable inputs.
The MAX3095/MAX3096 enter shutdown when G is low
and G is high. In shutdown, all outputs go high imped-
ance and the devices typically draw less than 1nA. The
devices exit shutdown by taking G high or G low. The
typical shutdown exit time is 600ns.
Table 1. Function Table
X = don’t care, High-Z = high impedance
G
X
X
X
1
1
1
0
G
X
X
X
0
0
0
1
Low-Power Shutdown Mode
≤ -200mV
≤ -200mV
≥ 200mV
≥ 200mV
(A - B)
Open
Open
X
OUTPUT
High-Z
Y
1
0
1
1
0
1
Machine Model
Shutdown
DEVICE
MODE
On
On
On
On
On
On