DHRB34A221M1CB Murata Electronics North America, DHRB34A221M1CB Datasheet - Page 6

• Manufacturer Part Number: DHRB34A221M1CB
• Description: CAP 10KV B RAD
• Manufacturer: Murata Electronics North America
• Series: DHRr

Specifications of DHRB34A221M1CB

• Capacitance: 220pF
• Voltage - Rated: 10000V (10kV)
• Tolerance: ±20%
• Temperature Coefficient: B
• Mounting Type: Through Hole
• Operating Temperature: -25°C ~ 85°C
• Applications: General Purpose
• Ratings: -
• Package / Case: Radial - Disc
• Size / Dimension: -
• Height: -
• Thickness: -
• Lead Spacing: -
• Features: High Voltage
• Lead Style: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: Q6021196

!Note
!Note
No.
(Note) Tests for Dielectric Strength (between lead wires), Charge Discharge Test, Humidity, Temperature Cycle and Life should be performed with
specimens having molded resin (MR1023C : made by Murata) extending over 3mm on all the surface.
* "room condition" Temperature: 15 to 35D, Relative humidity: 45 to 75%, Atmospheric pressure: 86 to 106kPa
1
2
3
4
5
6
7
8
9
Operating Temperature Range
Capacitance
Dissipation Factor (D.F.)
Insulation
Resistance (I.R.)
Dielectric
Strength
Temperature Characteristics
Soldering Effect
Humidity
(Under
Steady
State)
Life
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specificaions before ordering.
Item
Between
Lead Wires
Between
Lead Wires
Body Insulation
Appearance
Capacitance
Change
Dielectric Strength
(Between
Lead Wires)
Appearance
Capacitance
Change
D.F.
I.R.
Dielectric Strength
(Between
Lead Wires)
Appearance
Capacitance
Change
D.F.
I.R.
Dielectric Strength
(Between
Lead Wires)
-25 to +100˚C
Within the specified tolerance.
10000MΩ min.
No failure.
No failure.
No marked defect.
Within ±10%
No failure.
No marked defect.
Within ±10%
5000MΩ min.
No failure.
No marked defect.
Within ±10%
5000MΩ min.
No failure
Temp. Char.
ZM
ZM
ZM
ZM
B
B
B
B
Specifications
1.0% max.
2.5% max.
1.5% max.
4.0% max.
1.5% max.
4.0% max.
Temp. Coefficient or
-4700±1000ppm/˚C
Max. Cap. Change
±10%
The capacitance should be measured at 20°C with 1±0.2kHz
and AC 5V(r.m.s.) max.
Same condition as capacitance.
The insulation resistance should be measured with DC1000V
within 60±5 sec. of charging.
The capacitor should not be damaged when DC voltage of
150% of the rated voltage is applied between the lead wires for
60±5 sec. in insulating liquid or gas.
(Charge/Discharge currentV50mA)
The capacitor is placed in the container with
metal balls of diameter 1mm so that each
lead wire, shortcircuited, is kept
approximately 2mm off the metal balls as
shown in the figure at right, and DC voltage
of 3kV is applied for 10 sec. between
capacitor lead wires and metal balls.
(Charge/Discharge currentV50mA)
The capacitance measurement should be made at each step
specified in table.
Capacitance change from the value of step 3 should not
exceed the limit specified.
The lead wires should be immersed into the melted solder of
350±10˚C up to about 1.5 to 2.0mm from the main body for
3.5±0.5 sec.
Post-treatment: Capacitor should be stored for 24±2 hrs. at
*room condition.
Set the capacitor for 240±8 hrs. at 40±2˚C in 90 to 95% relative
humidity.
Post-treatment: Capacitor should be stored for 1 to 2 hrs. at
*room condition.
Apply a DC voltage of 125% of the rated voltage for 1000
hrs. in silicon oil at 85±2˚C.
Post-treatment: Capacitor should be stored for 24±2 hrs. at
*room condition.
(Charge/Discharge currentV50mA)
Specifications and Test Methods
Char.
ZM
B
Step
20±2˚C
—
1
-25±3˚C
Testing Method
—
2
—
Continued on the following page.
20±2˚C
20±2˚C
3
85±2˚C
85±2˚C
C41E2.pdf 03.4.16
4
Approx. 2mm
Metal balls
20±2˚C
20±2˚C
+48
-0
5
5
1