STUSB02EQR STMicroelectronics, STUSB02EQR Datasheet

no-image

STUSB02EQR

Manufacturer Part Number
STUSB02EQR
Description
TRANSCEIVER USB SGL 16-QFN
Manufacturer
STMicroelectronics
Type
USB Transceiverr
Datasheet

Specifications of STUSB02EQR

Number Of Drivers/receivers
1/1
Protocol
USB 2.0
Voltage - Supply
4 V ~ 5.5 V
Mounting Type
Surface Mount
Package / Case
16-QFN
For Use With
497-8209 - BOARD EVAL USB STUSB02E/ST72F63B
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
497-4983-2
General features
Description
The STUSB02E is a single chip USB transceiver
that supports both full-speed (12Mbps) and low-
speed (1.5Mbps) operation. It has an integrated
5V to 3.3V regulator which allows direct powering
from the V
voltage detector to detect the presence of the
V
Order code
March 2007
BUS
Supports 1.5Mbps and 12Mbps serial data
transmission
ESD HBM: ±14kV on D+, D– Lines; ±5kV on
VBUS
ESD Compliant to IEC-61000-4.2 (Level 3)
Separate I/O supply with operation down to
1.6V
Integrated speed select termination supply
Very low power consumption to meet USB
‘suspend’ current requirements
Small QFN16 lead free package
No power supply sequencing requirements
Software controlled re-enumeration
voltage.
BUS
STUSB02EQR
Part number
. The transceiver has an integrated
QFN16 (3mm x 3mm)
Package
Rev. 4
The transceiver also supports Sharing mode
when V
lines to be shared with other serial protocols.
It is also designed to operate down to 1.6V so that
it is compatible with lower system voltages of most
portable systems, which include PDAs, MP3
Player and Cell phones.
BUS
is not present, which allows the D+/D–
QFN16 (3mmx3mm)
USB Transceiver
3000 parts per reel
STUSB02E
Packaging
www.st.com
1/20
20

Related parts for STUSB02EQR

STUSB02EQR Summary of contents

Page 1

... BUS voltage detector to detect the presence of the V voltage. BUS Order code Part number STUSB02EQR March 2007 QFN16 (3mmx3mm) The transceiver also supports Sharing mode when V is not present, which allows the D+/D– BUS lines to be shared with other serial protocols. ...

Page 2

Contents Contents 1 Typical application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

Page 3

STUSB02E 1 Typical application Figure 1. Typical application Typical application 3/20 ...

Page 4

Pin configuration 2 Pin configuration Figure 2. Pin connections (top view) Table 1. Pin description PlN N° SYMBOL I SPD I 2 RCV I I/O 5 CON I ...

Page 5

STUSB02E 3 Functional tables Table 2. Function selection SUS OE# D Driving L H Receiving Hi-Z (1) During suspend VP and VM are active in order to detect out of band signalling ...

Page 6

Maximum ratings 4 Maximum ratings Table 4. Absolute maximum ratings Symbol V Supply voltage BUS V+ All other Inputs I Output current (D+, D Output current (all others Input current I D+, D-, HBM (Note 3) ...

Page 7

STUSB02E 5 Electrical characteristics Table 6. DC electrical characteristics (System and USB interface 3.6V unless otherwise noted BUS -40 to 85°C) Symbol Parameter V USB Supply voltage BUS V System I/F supply voltage ...

Page 8

Electrical characteristics Table 7. DC electrical characteristics (System and USB interface 3.6V unless otherwise noted BUS Symbol Parameter V USB Supply voltage BUS V System I/F supply voltage IF V Low level input ...

Page 9

STUSB02E Table 9. DC electrical characteristics (Transceiver 3.6V unless otherwise noted BUS -40 to 85°C) Symbol Parameter Hi-Z State data line leakage I LO (suspend mode) V Differential input sensitivity DI V Differential ...

Page 10

Electrical characteristics Table 11. AC electrical characteristics (V = 3.6V unless otherwise noted BUS Symbol Parameter T Transition Rise Time (LOW SPEED Transition Fall Time (LOW SPEED) F Rise/Fall Time Matching (LOW T ...

Page 11

STUSB02E 6 Timing diagram Figure 3. Enable and disable times Figure 4. Rise and fall times Timing diagram 11/20 ...

Page 12

Timing diagram Figure 5. Receiver propagation delay Figure 6. Driver propagation delay (C Minimum Timing LS and maximum timing FS Figure 7. Enable and disable time circuit Switch = GND for t and VTRM for t ...

Page 13

STUSB02E 7 Test circuits Figure 8. Load for VP, VM, RCV Figure 9. Load for D+, D- Test circuits 13/20 ...

Page 14

Test circuits Figure 10. Functional diagram 14/20 STUSB02E ...

Page 15

STUSB02E 8 Functional description The STUSB02E is designed to provide USB connectivity in mobile systems where available system supply voltages are not able to satisfy USB requirements. The STUSB02E can operate down to supply voltages of 1.6V. As shown in ...

Page 16

Package mechanical data 9 Package mechanical data In order to meet environmental requirements, ST offers these devices in ECOPACK These packages have a Lead-free second level interconnect. The category of second Level Interconnect is marked on the package and on ...

Page 17

STUSB02E DIM. MIN 0. QFN16 (3mmx3mm) MECHANICAL DATA mm. TYP MAX. 0.90 1.00 0.02 0.05 0.20 0.25 0.30 3.00 1.70 1.80 ...

Page 18

Package mechanical data Tape & Reel QFNxx/DFNxx (3x3) MECHANICAL DATA DIM. MIN 12 18/20 mm. TYP MAX. MIN. 330 13.2 0.504 0.795 2.362 18.4 3.3 3.3 1.1 4 ...

Page 19

STUSB02E 10 Revision history Table 12. Revision history Date Revision 19-Oct-2005 1 21-Feb-2006 2 07-Apr-2006 3 14-Mar-2007 4 First Release. Declaration of conformity with USB 2.0 specification removed. Corrected wrong links to figures in table 11. Update tape & reel. ...

Page 20

... Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale. ...

Related keywords