LTC1569IS8-7#TR Linear Technology, LTC1569IS8-7#TR Datasheet - Page 5

• Manufacturer Part Number: LTC1569IS8-7#TR
• Description: IC FILTER LP 10TH ORD LIN 8SOIC
• Manufacturer: Linear Technology

Specifications of LTC1569IS8-7#TR

• Filter Type: Linear Phase, Lowpass Switched Capacitor
• Frequency - Cutoff Or Center: 300kHz
• Number Of Filters: 1
• Max-order: 10th
• Mounting Type: Surface Mount
• Package / Case: 8-SOIC (3.9mm Width)
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Voltage - Supply: -

BLOCK DIAGRA
IN
both input pins. The DC gain from IN
(Pin 8) is 1.0, and the DC gain from Pin 2 to Pin 8 is –1. The
input range, input resistance and output range are de-
scribed in the Applications Information section. Input
voltages which exceed the power supply voltages should
be avoided. Transients will not cause latchup if the current
into/out of the input pins is limited to 20mA.
GND (Pin 3): The GND pin is the reference voltage for the
filter and should be externally biased to 2V (1.11V) to
maximize the dynamic range of the filter in applications
using a single 5V (3V) supply. For single supply operation,
the GND pin should be bypassed with a quality 1 F
ceramic capacitor to V
circuit biasing the GND pin should be less than 2k as the
GND pin generates a small amount of AC and DC current.
For dual supply operation, connect Pin 3 to a high quality
DC ground. A ground plane should be used. A poor ground
will increase DC offset, clock feedthrough, noise and
distortion.
V
quality 1 F ceramic bypass capacitor is required from V
(Pin 7) to V
internal clock drivers. The bypass should be as close as
possible to the IC. In dual supply applications (Pin 3 is
grounded), an additional 0.1 F bypass from V
GND (Pin 3) and V
mended.
The maximum voltage difference between GND (Pin 3) and
V
PIN
–
+
+
/V
U
(Pin 7) should not exceed 5.5V.
/IN
+
FUNCTIONS
–
(Pins 4, 7): For 3V, 5V and 5V applications a
(Pins 1, 2): Signals can be applied to either or
U
–
(Pin 4) to provide the transient energy for the
–
U
(Pin 4) to GND (Pin 3) is recom-
–
(Pin 4). The impedance of the
W
GND
IN
IN
V
+
–
–
+
1
2
3
4
(Pin 1) to OUT
+
(Pin 7) to
FILTER NETWORK
LINEAR PHASE
CONTROL
10TH ORDER
POWER
+
OSCILLATOR
PRECISION
DIVIDER/
BUFFER
DIV/CLK (Pin 5): DIV/CLK serves two functions. When the
internal oscillator is enabled, DIV/CLK can be used to
engage an internal divider. The internal divider is set to 1:1
when DIV/CLK is shorted to V
is set to 4:1 when DIV/CLK is allowed to float (a 100pF
bypass to V
to 16:1 when DIV/CLK is shorted to V
divide-by-4 and divide-by-16 modes the power supply
current is reduced by typically 60%.
When the internal oscillator is disabled (R
to V
external clock signal. For proper filter operation, the clock
waveform should be a squarewave with a duty cycle as
close as possible to 50% and CMOS voltages levels (see
Electrical Characteristics section for voltage levels). DIV/
CLK pin voltages which exceed the power supply voltages
should be avoided. Transients will not cause latchup if the
fault current into/out of the DIV/CLK pin is limited to 40mA.
R
pin and V
of the resistor determines the frequency of oscillation. The
maximum recommended resistor value is 40k and the
minimum is 3.8k/8k (single 5V/3V supply). The internal
oscillator is disabled by shorting the R
(Please refer to the Applications Information section.)
OUT (Pin 8): Filter Output. This pin can drive 10k and/or
40pF loads. For larger capacitive loads, an external 100
series resistor is recommended. The output pin can ex-
ceed the power supply voltages by up to 2V without
latchup.
X
(Pin 6): Connecting an external resistor between the R
–
) DIV/CLK becomes an input pin for applying an
+
(Pin 7) enables the internal oscillator. The value
8
7
6
5
–
OUT
V
R
DIV/CLK
is recommended). The internal divider is set
+
X
1569-7 BD
R
EXT
–
(Pin 4). The internal divider
LTC1569-7
X
pin to V
+
(Pin 7). In the
X
–
shorted
(Pin 4).
5
X