NT-54D0-0487 LAMINA, NT-54D0-0487 Datasheet - Page 13

• Manufacturer Part Number: NT-54D0-0487
• Description: LED MODULE, DAYLIGHT WHITE, 1853LM
• Manufacturer: LAMINA
• Series: Titan Turbor

Specifications of NT-54D0-0487

• Led Module Type: Board + LED + Connector
• Led Color: Daylight White
• Cct: 4700K
• Luminous Flux @ Test: 1853lm
• Supply Voltage: 11.3V
• Forward Current @ Test: 5A
• Power Rating: 56.5W
• Rohs Compliant: Yes
• Power Module Configuration: Circular

©2008 L
t
itan
t
urbo
amina
tm
p
a
Led L
L
ighting
aTenTS anD
SSeMbLy anD
ight
i
ncorporated
e
ngines
p
Lamina’s light engines may be covered by pending patents and/or one or more of the following U.S.
and/or International patents 5876536, 6709749 B, 595880, 6017642, 5565262, 5681444, 5653834,
5581876, 5847935, 5514451, 5747931, 5925203, 5725808, 5929510, 5858145, 5866240, 5953203,
6055151, 614076, 6011330, 6399230, 6914501, 6168490, 6191934, 614075, 6160469, 6300267,
6471805, 6518502, 6739047, 6720859, 6759940, 6518502, 6670856 B1, 6720859, 6713862 B2, WO
00/47399, WO 00/26152, WO 98/19339, 5082804, ZL99808762.9, 69623930, 69628549, 69629572,
805785, 69628549, 843621, 932500, 805785, 812258, 843621, 932500, 805785, 812258, 843621,
932500, 805785, 812258, 843621, 932500, 3327556, 3267299, 3226281, 3405545, 320630, 295695,
284068, 546471, 805785, 812258, 843621, 6455930, 6759940, 6713862, 7095053, 7098483.
e
LED light engines are available with or without Lamina’s EZ-Connect board. EZ-Connect adapter
boards have AMP connectors for solderless connections to Lamina’s wiring harness.
As with many electrical devices, non-acid RMA type solder flux should be used to prepare the solder
pads before application of solder. Ensure proper strain relief of wires attached to the light engine to
prevent damage to the light engines solder pads. For more information refer to Lamina’s connection
application note AN-05 which can be found on the website at www.laminalighting.com.
Functional test: Parts may be tested using a constant current source set at 25% of Drive Current for
no more than two seconds without heat sink.
1.
2.
r
Your parts will arrive in either custom fitted trays or on easy to use tape and reel packaging. This
packaging was designed to provide the necessary protection during shipment and to take up the
least amount of space in your storage area.
Notes
1.
2.
3.
4.
aTenTS
LeCTriCaL
eCeiving
Fm-0194 r
Optical and electrical specifications are given for the specified drive @ 25ºC junction
temperature.
When using constant current LED drivers with high compliance voltage (Advance, LEDworks,
etc. or a custom driver) the output of the supply must be connected to the part before power is
applied to the input of the supply.
This product uses silicone materials for superior optical performance. Do not expose the part to
fluids that may react with silicone compounds. See Dow Chemical Form 45-0113D-01, Silicone
Fluid Resistance Guide.
Ray trace models are available upon request.
Lamina may make process or materials changes affecting the performance or other
characteristics of our products. These products supplied after such changes will continue to
meet published specifications, but may not be identical to product supplied as samples or
under prior orders.
All specifications are based on mounting the LED array to a heat sink using the specified
hardware and thermal grease Wakefield P/N 120. The heat sink must meet the specified
flatness requirement. Mounting using screws and thermal tape may damage the device.
C
ev
p
p
05.21.08
onneCTionS
C
arTS anD
aCkaging
onneCTionS
p
aCkaging
T
rayS
t
itan
t
urbo
tm