SRT2-ATT02 Omron, SRT2-ATT02 Datasheet - Page 3

• Manufacturer Part Number: SRT2-ATT02
• Description: BRACKET MNT SURFACE
• Manufacturer: Omron

Specifications of SRT2-ATT02

• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: SRT2ATT02

SRT2-VID/VOD
Specifications
3 RATINGS
Inputs
Outputs
Note: When using V/G terminals in an MIL connector, ensure that the current per terminal for the V/G terminals does not exceed 1 A.
3 CHARACTERISTICS
Note: The above current consumption is the value with all points turned ON excluding the current consumption of the external sensor
Input current
ON delay time
OFF delay time
ON voltage
OFF voltage
OFF current
Insulation method
Maximum number of inputs
Number of circuits
Rated output current
Residual voltage
ON delay time
OFF delay time
Leakage current
Insulation method
Number of circuits
Communications power supply
voltage
I/O power supply voltage
I/O power supply current
Current consumption (See Note)
Noise immunity
Vibration resistance
Shock resistance
Dielectric strength
Ambient temperature
Ambient humidity
Mounting strength
Terminal strength
Screw tightening torque
Node address setting
Weight
connected to the input Remote Terminal and the current consumption of the load connected to the output Remote Terminal.
Item
Item
6 mA max./point at 24 V, 3 mA max./point at 17 V
1.5 ms max.
1.5 ms max.
15 VDC min. (Between each input terminal and V: NPN. Between each input and G: PNP.)
5 VDC max. (Between each input terminal and V: NPN. Between each input and G: PNP.)
1 mA max.
Photocoupler
8
8 points/common, 1 circuit
0.3 A/point
1.2 V max.
0.5 ms max.
1.5 ms max.
0.1 mA max.
Photocoupler
8 points/common, 1 circuit
14 to 26.4 VDC
20.4 to 26.4 VDC (24 VDC
Sensor connector: 2.4 A max., MIL ribbon style connector: 2.0 A max.
50 mA max. at 24 VDC
10 to 150 Hz, 1.0 mm double amplitude or 70 m/s
200 m/s
500 VAC between insulated circuits
Operating:
Storage:
Operating:
Storage:
No damage when 100 N pull load was applied in all directions (40 N load for SRT2-ATT02)
No damage when the following loads were applied:
Communications connector: 100 N
Sensor connector: 40 N
MIL connector: 100 N
Communications connector: 0.25 N : m
Settings made at DIP switch (set before supplying power for Slave communications)
Approx. 75 g max.
1,500 V with a pulse width of 100 ns to 1 s and 1 ns onset (tested with noise simulator)
2
--10 C to 55 C (14 F to 131 F) with no icing or condensation
--25 C to 65 C (--13 F to 149 F) with no icing or condensation
25% to 85% with no condensation
25% to 85%
SRT2-VID08S-1
SRT2-VID08S-1
SRT2-VID08S
SRT2-VID08S
+10%
/
- -15%
)
12
16 points/common, 1 circuit
0.3 A/point, 2 A common (See Note.)
16 points/common, 1 circuit
2
(50 m/s
2
for SRT2-ATT02)
SRT2-VID16ML-1
SRT2-VID16ML-1
SRT2-VID16ML
SRT2-VID16ML
SRT2-VID/VOD
3