B7A-T10M2 Omron, B7A-T10M2 Datasheet - Page 3

• Manufacturer Part Number: B7A-T10M2
• Description: TERM BLOCK PLC 10POS TTL IN PCB
• Manufacturer: Omron

Specifications of B7A-T10M2

• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: B7AT10M2

B7A-P P P P 10
Specifications
3 CHARACTERISTICS
General
Note: 1. The transmission distance values stated in this table are based on one power supply attached to each Input or Output Link
Input Models
Note: 1. The polarity of the B7A-TS10S1’s BP terminal is negative. Therefore, supply power to the three-wire sensor from the positive
Communication method
Transmission distance (See Note 1)
I/O delay
Minimum input time (See Note 2)
Operating voltage range
Insulation resistance
Dielectric strength
Noise immunity
Vibration resistance
Shock resistance
Ambient temperature
Ambient humidity
Compatible inputs
Input logic
Current consumption
(See Note 2)
Input voltage range
Operating voltage
range
Input current range
Minimum input time
ON/OFF threshold
Mounting strength
Terminal strength
Tightening torque
Weight
2. The minimum input time is required for the B7A/B7AS to read an input signal.
2. Consumption when all 10 points are ON. Excludes external sensor current for Input Modules.
3. The minimum input time is required for the B7A to read an input signal.
Terminal. If two Input or Output Link Terminals share one power supply, the transmission distance will be derated, and the volt-
age must be 24 VDC 10%. The derated transmission distance for normal-speed models is 100 m maximum and that of a
high--speed model is 50 m maximum.
power supply terminal or a power supply.
Item
Item
Switches, three-wire NPN sensors (See Note 1)
Active low
80 mA max. with all input terminals ON
0 VDC to supply voltage
12 to 24 VDC
16 ms (See Note 3)
No--contact input:
Contact input:
No damage when 5--kgf (49 N) pull is applied for 1 min each in all
directions (except direction of DIN track)
No damage when 5--kgf (49 N) pull is applied for 1 min each in all
directions
8 to 12 kgf : cm (0.78 to 1.18 N : m)
Approx. 100 g
--4.4 to --1.1 mA/point (current flowing from input terminals)
B7A-T10S1
Unidirectional, time--division multiplex
500 m max.
Typical: 19.2 ms; 31 ms max.
16 ms
12 to 24 VDC (10.8 to 26.4 VDC) (See Note 1)
100 M min. (500 V) between each terminal and external parts
1,000 VAC, 50/60 Hz for 1 min between each terminal and external parts
Noise level: 1.5 kV; pulse width: 100 ns to 1 s (on transmission line due to coupling)
10 to 55 Hz, 1.5-mm double amplitude
300 m/s
Operating: --10 C to 55 C (14 F to 131 F) with no icing
Storage:
Operating: 35% to 85% with no condensation
ON voltage:
OFF voltage:
ON discrimination resistance:
OFF discrimination resistance: 5 k
Screw terminal models
2
(approx. 30G)
--25 C to 65 C (--13 F to 149 F) with no icing
1.6 V max.
5.5 V min.
B7A-T10S3
Normal speed
140
min.
max.
TTLs, switches
Active high
40 mA max. with all input terminals
ON
0 to 5 VDC 10%
1.7 to 2.2 mA/point
ON voltage:
OFF voltage:
------
------
------
Approx. 12 g
Printed circuit board models
B7A-T10M2
2.2 V min.
0.8 V max.
B7A-P P P P 10
3