MAX9258GCM+T Maxim Integrated Products, MAX9258GCM+T Datasheet - Page 36
![IC SER/DESER PROG 48-LQFP](/photos/6/55/65521/48-lqfp_21-0054f_sml.jpg)
MAX9258GCM+T
Manufacturer Part Number
MAX9258GCM+T
Description
IC SER/DESER PROG 48-LQFP
Manufacturer
Maxim Integrated Products
Datasheet
1.MAX9257GTL.pdf
(52 pages)
Specifications of MAX9258GCM+T
Function
Serializer/Deserializer
Data Rate
840Mbps
Input Type
Serial
Output Type
LVDS
Number Of Inputs
1
Number Of Outputs
16
Voltage - Supply
3 V ~ 3.6 V
Operating Temperature
-40°C ~ 105°C
Mounting Type
Surface Mount
Package / Case
48-LQFP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Fully Programmable Serializer/Deserializer
with UART/I
The ECU writes the sync frame, 7-bit device address
plus read/write bit (R/W = 1 for read), 8-bit register
address, and number of bytes to be read. The
addressed device responds with read data bytes
(Figure 29). UART read delay is maximum 4 bit times
when reading from the MAX9257 or the MAX9258.
Up to two high bit times are allowed between frames.
A high time ranging from 14 UART bit times or more
resets the packet boundary. In this case, the next frame
received is assumed to belong to a new packet by the
MAX9257/MAX9258 and UART-to-I
Resetting the boundary is required. Not resetting the
boundary treats the following packets as part of the first
packet, and they may be processed incorrectly.
The control channel data rate in base mode is between
95kbps to 4.25Mbps (Table 28). In bypass mode, the
allowed data rate is DC to 10Mbps (Table 29). For data
rates faster than 4.25Mbps in bypass mode, REG8[5] in
MAX9257 and REG7[5] in MAX9258 must be set high.
Set the control channel data rate in base mode by writ-
ing to REG8[1:0] in the MAX9257 and REG7[1:0] in the
MAX9258. These write commands take effect in the
next control channel.
Programming the FAST bit takes effect in the same con-
trol channel. Both the MAX9257 and the MAX9258
should have the same settings for FAST. It is recom-
mended to first program the FAST bit in the MAX9257.
Programming FAST to 1 results in shorter UART pulses
on the differential link.
The MAX9257/MAX9258 have device addresses that
can be programmed to any 7-bit address. Table 30
shows the default addresses.
36
______________________________________________________________________________________
MAX9257/MAX9258 Device
Address Programming
Reset of Packet Boundary
2
C Control Channel
Time Between Frames
2
C converter.
Read Packet
Data Rate
Figure 29. UART Read Packet
Table 28. Control Channel Data Rate in
Base Mode
Table 29. Control Channel Data Rate in
Bypass Mode
Table 30. Default Device Address
MAX9257
MAX9258
DEVICE
MAX9257 REG8[1:0]
MAX9258 REG7[1:0]
SYNC
MAX9257 REG8[5]
MAX9258 REG7[5]
DEV ADDR +
R/W
00
01
10
11
0
1
REG ADDRESS
1111 1010
1111 1000
BINARY
NUMBER OF BYTES
DEFAULT
4.25Mbps–10Mbps
1Mbps–4.25Mbps
1Mbps–4.25Mbps
95kbps–400kbps
400kbps–1Mbps
DC–4.25Mbps
BYTE 1
RANGE
(default)
RANGE
0xFA
0xF8
HEX
BYTE N