120677-1 TE Connectivity, 120677-1 Datasheet - Page 2
![High Speed / Modular Connectors Z-PACK](/photos/39/85/398554/pr6w45050b_sml.jpg)
120677-1
Manufacturer Part Number
120677-1
Description
High Speed / Modular Connectors Z-PACK
Manufacturer
TE Connectivity
Series
120677r
Specifications of 120677-1
Number Of Rows
6
Number Of Positions / Contacts
30
Pitch
2 mm
Mounting Style
Through Hole
Termination Style
Solder Pin
Housing Material
Glass Filled Polyester
Contact Material
Phosphor Bronze
Contact Plating
Gold over Nickel
Product Type
Connector
Connector Type
Header
Pcb Mounting Orientation
Vertical
Module Type
Right
Solder Tail Contact Plating
Tin-Lead over Nickel
Termination Post Length (mm [in])
3.70 [0.146]
Card Slot Pitch (mm [in])
17.8 [0.7]
Rows Per Connector
6
Columns Per Connector
5
Number Of Signal Contacts
30
Centerline (mm [in])
2.00 [0.079]
Contact Type
Pin
Contact Style
Press Fit, Short Tail
Guide Pin Style
ESD/HDI
Contact Base Material
Phosphor Bronze
Contact Configuration
Grounding
Contact Mating Area Length (mm [in])
8.20 [0.323]
Contact Plating, Mating Area, Material
Conforms to Performance Requirements of TE Connectivity Product Specification 108-1957; Based on Telcordia GR-1217-CORE, Applications in Uncontrolled Environments
Connector Style
Plug
Rohs/elv Compliance
RoHS compliant, ELV compliant
Lead Free Solder Processes
Not relevant for lead free process
Rohs/elv Compliance History
Always was RoHS compliant
Lead Free Status / Rohs Status
Details
3.3.
3.4.
3.5.
Rev C
Initial examination of product.
Final examination of product.
Dry circuit resistance.
Change in resistance.
Insulation resistance.
Dielectric withstanding voltage.
Compliant pin resistance.
Ratings
!
!
!
!.
Performance and Test Description
Product is designed to meet the electrical, mechanical and environmental performance requirements
specified in Figure 1. Unless otherwise specified, all tests shall be performed at ambient environmental
conditions per EIA-364.
Test Requirements and Procedures Summary
Test Description
Voltage: 250 volts AC
Current: 1.15 ampere (100% loaded)
Temperature: -65 to 105° C
Characteristic Impedance: 50 ohms (single ended), 100 ohms (differential)
Meets requirements of product
drawing.
Meets visual requirements.
20 milliohms maximum for both
signal and ground contacts.
∆R <5 milliohms average value,
<10 milliohms individual reading for
both signal and ground contacts.
10000 megohms minimum.
600 volts AC at sea level,
signal/signal.
300 volts AC at sea level,
signal/ground.
1 minute hold with no breakdown or
flashover.
1 milliohm maximum initial.
∆R 1 milliohm maximum from
initial.
Figure 1 (continued)
ELECTRICAL
Requirement
EIA-364-18.
Visual and dimensional inspection
per product drawing.
EIA-364-18.
Visual inspection.
EIA-364-23.
Subject specimens to 100
milliamperes maximum and 20
millivolts maximum open circuit
voltage.
See Figure 3.
EIA-364-21.
Test between adjacent contacts of
mated specimens.
EIA-364-20.
Test between adjacent contacts or
ground shield of mated specimens.
EIA-364-23.
Subject specimens to 100
milliamperes maximum and 20
millivolts maximum open circuit
voltage. Measurements taken
between PCB hole and bottom of
pin.
Procedure
108-1957
2 of 7