CP2102-GM Silicon Laboratories Inc, CP2102-GM Datasheet - Page 11

• Manufacturer Part Number: CP2102-GM
• Description: IC USB-TO-UART BRIDGE 28VQFN
• Manufacturer: Silicon Laboratories Inc

Specifications of CP2102-GM

• Package / Case: 28-VQFN Exposed Pad, 28-HVQFN, 28-SQFN, 28-DHVQFN
• Applications: USB
• Interface: UART
• Voltage - Supply: 3 V ~ 3.6 V
• Mounting Type: Surface Mount
• Maximum Operating Temperature: + 125 C
• Minimum Operating Temperature: - 55 C
• Mounting Style: SMD/SMT
• Operating Supply Voltage: 3.6 V
• Supply Current (max): 100 mA
• Operating Temperature (min): -40C
• Operating Temperature Classification: Industrial
• Operating Temperature (max): 85C
• Package Type: QFN
• Rad Hardened: No
• Usb Version: 2.0
• Data Rate: 1Mbps
• Supply Voltage Range: 1.8V To 3.6V, 3V To 3.6V
• Operating Temperature Range: -40°C To +85°C
• Digital Ic Case Style: MLP
• No. Of Pins: 28
• Filter Terminals: SMD
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 336-1161 - KIT EVALUATION FOR CP2102
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1160; CP2102

5. USB Function Controller and Transceiver
The Universal Serial Bus function controller in the CP2102 is a USB 2.0 compliant full-speed device with integrated
transceiver and on-chip matching and pull-up resistors. The USB function controller manages all data transfers
between the USB and the UART as well as command requests generated by the USB host controller and
commands for controlling the function of the UART.
The USB Suspend and Resume signals are supported for power management of both the CP2102 device as well
as external circuitry. The CP2102 will enter Suspend mode when Suspend signaling is detected on the bus. On
entering Suspend mode, the CP2102 asserts the SUSPEND and SUSPEND signals. SUSPEND and SUSPEND
are also asserted after a CP2102 reset until device configuration during USB Enumeration is complete.
The CP2102 exits the Suspend mode when any of the following occur: (1) Resume signaling is detected or
generated, (2) a USB Reset signal is detected, or (3) a device reset occurs. On exit of Suspend mode, the
SUSPEND and SUSPEND signals are de-asserted.
Both SUSPEND and SUSPEND temporarily float high during a CP2102 reset. If this behavior is undesirable, a
strong pulldown (10 kΩ) can be used to ensure SUSPEND remains low during reset. See Figure 6 for other
recommended options.
Option 1: A 4.7 kΩ pull-up resistor can be added to increase noise immunity.
Option 2: A 4.7 µF tantalum capacitor can be added if powering other devices from the on-chip regulator.
Option 3: Avalanche transient voltage suppression diodes should be added for ESD protection .
Option 3:
Option 4: 10 kΩ resistor to ground to hold SUSPEND low on initial power on or device reset.
CONNECTOR
USB
VBUS
GND
D+
D-
Use Littlefuse p/n SP0503BAHT or equivalent.
1
3
4
4.7 µF
Option 2
TANT
C4
D1
0.1 µF
D2
1 µF
C1
C2
D3
7
6
3
8
5
4
Option 3
Figure 6. Typical Connection Diagram
REGIN
VBUS
VDD
GND
D+
D-
CP2102
Rev. 1.0
SUSPEND
SUSPEND
RST
DCD
DTR
DSR
TXD
RXD
RTS
CTS
RI
9
12
11
2
1
28
27
26
25
24
23
4.7 kΩ
10 kΩ
R1
R2
VDD
Option 1
Option 4
External RS-232
(to external circuitry
for USB suspend
states)
UART circuitry
transceiver or
CP2102
11