R88M-W10030H-S1 Omron, R88M-W10030H-S1 Datasheet - Page 372
![no-image](/images/manufacturer_photos/0/4/494/omron_sml.jpg)
R88M-W10030H-S1
Manufacturer Part Number
R88M-W10030H-S1
Description
SERVOMOTOR 100W 3000RPM INC KEY
Manufacturer
Omron
Datasheet
1.R88A-PR02W.pdf
(458 pages)
Specifications of R88M-W10030H-S1
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
R88MW10030HS1
- Current page: 372 of 458
- Download datasheet (5Mb)
Operation
• Store the online auto-tuning results if you want to use the results as the initial value when the power
Operation Procedure
Note 1. The digits you can manipulate will flash.
Note 2. “
4-11-3 Servomotor Origin Search
H Servomotor Origin Search (Fn003)
• The Servomotor origin search function rotates the Servomotor to the encoder’s origin pulse (phase Z)
• Use this function to adjust the origin position of the Servomotor shaft and mechanical system.
Note 1. Execute the Servomotor origin search before connecting the Servomotor shaft and mechani-
Note 2. The RUN command input must be turned OFF. Also, if the RUN signal is set to be always ON
4-134
(Approx. 1 s later)
supply is next turned ON again. Performing this operation writes the results to Pn103 (inertia ratio).
operation
position, and then stops the Servomotor.
PR02W
Online auto-tuning results
stored
System Check Mode
shows a display of 200%).
cal system.
(Pn50A.1 = 7), either change the setting to “Always OFF” (setting value: 8) or change the set-
ting to another value, then turn OFF the power supply once, and then turn it ON again.
jjjj
key operation
Front panel
(1 s min.)
(1 s min.)
“ denotes the inertia ratio (%) calculated by online auto-tuning. (The example given
Display
1 s min.
1 s min.
Press the MODE/SET Key to change to System Check
Mode.
Press the Up or Down Key to set function code Fn007.
(See note 1.)
Press the DATA Key (front panel: DATA Key for 1 s min.)
to display “d.jjjj.” (See note 2.)
Press the MODE/SET Key to write the tuning results to
Pn103 (inertia ratio). When writing is complete, “donE”
will flash for approximately 1 s.
After “donE” has been displayed, the display will return
to “d.jjjj.”
Press the DATA Key (front panel: DATA Key for 1 s
min.). The display will return to the System Check Mode
function code.
(1 s later)
Explanation
Tuning results (inertia ratio) dis-
played (d.jjjj displayed)
“donE” flashes (Pn103
setting complete)
Display returns to
d.jjjj
Press this key to write
tuning results
Chapter 4
Related parts for R88M-W10030H-S1
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![G6S-2G](/images/no-image3.png)
Part Number:
Description:
G6S-2GLow Signal Relay
Manufacturer:
Omron Corporation
Datasheet:
![G3NE-220T](/images/no-image3.png)
Part Number:
Description:
Compact, Low-cost, SSR Switching 5 to 20 A
Manufacturer:
Omron Corporation
Datasheet:
![G6K-2G-Y](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
Omron Corporation
Datasheet:
![G4A-1A-E](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
Omron Corporation
Datasheet:
![G5NB-1A-E](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
Omron Corporation
Datasheet:
![G6B-2114P-US](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
Omron Corporation
Datasheet: