R7M-A75030 Omron, R7M-A75030 Datasheet - Page 168
R7M-A75030
Manufacturer Part Number
R7M-A75030
Description
MOTORSERVO CYLINDER 750W W/O KEY
Manufacturer
Omron
Datasheet
1.R7A-CNA02R.pdf
(252 pages)
Specifications of R7M-A75030
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
R7MA75030
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
R7M-A75030-S1
Manufacturer:
CINCH
Quantity:
200
- Current page: 168 of 252
- Download datasheet (4Mb)
●
• Ground the motor’s frame to the machine ground when the motor is on a movable shaft.
• Use a grounding plate for the frame ground for each Unit, as shown in the above diagrams, and
• Use ground lines with a minimum thickness of 3.5 mm
• If no-fuse breakers are installed at the top and the power supply line is wired from the lower duct,
• No-fuse breakers, surge absorbers, and noise filters (NF) should be positioned near the input termi-
• Wire the noise filter as shown at the left in the following illustration. The noise filter should be
3-28
System Design and Installation
AC
power
supply
Note 1. The cable wiring for the ferrite core must be 1.5 turns.
Note 2. Remove the sheath from the cable and ground it directly to the metal plate at the clamps.
Class D
ground
(Class 3
ground:
100 Ω or
less)
ground to a single point.
lines are as short as possible.
use metal tubes for wiring and make sure that there is adequate distance between the input lines
and the internal wiring. If input and output lines are wired together, noise resistance will decrease.
nal block (ground plate), and I/O lines should be isolated and wired using the shortest distance pos-
sible.
installed at the entrance to the control box whenever possible.
Three-phase Power Supply Input (R7D-AP08H)
Metal
duct or
conduit
Correct: Separate input and output
AC input
Ground
Control panel
Metal plate
NFB
Ground
plate
2 m max.
2 m max.
Surge
absorber
1
2
3
NF
E
Controller
power supply
4
5
6
AC output
Noise
filter
Noise
filter
Brake
power
supply
Contactor
Controller
L1C
L2C
L1
L2
L3
R7D-A@
CN1
2
CN2
, and arrange the wiring so that the ground
W
U
V
Ferrite core
Ferrite core
Clamp
AC input
Ground
AC output
Wrong: Noise not filtered effectively
Ferrite
core
Clamp
Ferrite
core
1
2
3
Metal
duct or
conduit
NF
E
Installation incorporating
Servo Motor
4
5
6
Ferrite
core
Ferrite
core
Chapter 3
R7M-A@
M
B
E
Related parts for R7M-A75030
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
MOTOR SERVO CYLINDER 30W W/O KEY
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
MOTOR SERVO CYLINDER 30W W/KEY
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
MOTOR SERVO CYLINDER 50W W/O KEY
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
MOTOR SERVO CYLINDER 50W W/KEY
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
MOTOR SERVO CYLINDER 100W W/O KE
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
MOTORSERVO CYLINDER 100W W/KEY
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
MOTORSERVO CYLINDER 200W W/O KEY
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
MOTORSERVO CYLINDER 200W W/KEY
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
MOTORSERVO FLAT 100W W/O BK&KEY
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
MOTORSERVO FLAT 100W W/O BK W/KE
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
MOTOR SERVO CYLINDER 30W W/BRAKE
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
MOTOR SERVO CYLINDER 30W W/BK&KE
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
MOTOR SERVO CYLINDER 50W W/BRAKE
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
MOTOR SERVO CYLINDER 50W W/BK&KE
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
MOTORSERVO FLAT 200W W/O BK&KEY
Manufacturer:
Omron
Datasheet: