R88M-WP10030S-BS1 Omron, R88M-WP10030S-BS1 Datasheet - Page 347
![no-image](/images/manufacturer_photos/0/4/494/omron_sml.jpg)
R88M-WP10030S-BS1
Manufacturer Part Number
R88M-WP10030S-BS1
Description
SERVO MOTOR 100W 100V W/BRAKE
Manufacturer
Omron
Datasheet
1.R88A-PR02W.pdf
(458 pages)
Specifications of R88M-WP10030S-BS1
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
R88MWP10030SBS1
- Current page: 347 of 458
- Download datasheet (5Mb)
Operation
4-8-2
H Functions
• This function shortens the positioning time by automatically adding the command pulse input (CW/
• Perform feed-forward compensation to increase servo gain efficiency, thus improving responsive-
Note Refer to Position Loop Block Diagram in 4-7-2 Manual Tuning for the internal processing block
H Parameters Requiring Settings
Note When not using the feed-forward function, set Pn10A to 0.
H Setting Procedure
• Finish adjusting the gain before adjusting the feed-forward.
• Increase the Pn109 (feed-forward amount) setting until positioning time is minimal. At this point, if
• If the overshoot is too large, increase Pn10A (feed-forward command filter) to reduce the it.
4-8-3
H Functions
• The torque feed-forward function reduces the acceleration time by adding the value of TREF (torque
• Normally a differential value is generated in the controller and this value is input to TREF.
• Overshooting will occur if the feed-forward amount (the voltage input to TREF) is too high, so adjust
Pn109
Pn10A
CCW) differential value to the speed loop in the Servo Driver.
ness. There is very little effect, however, on systems with sufficiently high position loop gain.
there are no problems with using overshoot, adjustments are complete. A high setting may cause the
machinery to vibrate. With ordinary machinery, set the gain to 80% maximum. (Adjust the gain while
checking the machine response.)
command input) to the current loop; it can be used with speed control.
Pn400 (torque command scale) as required.
Parameter No.
configuration.
Feed-forward Function (Position)
Torque Feed-forward Function (Speed)
Feed-forward
amount
Feed-forward
command filter
Parameter
name
Set the feed-forward gain (setting rage: 0 to 100
(%)).
Set the feed-forward command filter (primary lag).
(Setting range: 0 to 6400 (x 0.01 ms).)
Explanation
4-4-4 Parameter
Details
Chapter 4
Reference
4-109
Related parts for R88M-WP10030S-BS1
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![G6S-2G](/images/no-image3.png)
Part Number:
Description:
G6S-2GLow Signal Relay
Manufacturer:
Omron Corporation
Datasheet:
![G3NE-220T](/images/no-image3.png)
Part Number:
Description:
Compact, Low-cost, SSR Switching 5 to 20 A
Manufacturer:
Omron Corporation
Datasheet:
![G6K-2G-Y](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
Omron Corporation
Datasheet:
![G4A-1A-E](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
Omron Corporation
Datasheet:
![G5NB-1A-E](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
Omron Corporation
Datasheet:
![G6B-2114P-US](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
Omron Corporation
Datasheet:
![G6D-1A-ASI](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
Omron Corporation
Datasheet:
![G8P-1A4P](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
Omron Corporation
Datasheet: