3342-7 Peregrine Semiconductor, 3342-7 Datasheet
3342-7
Specifications of 3342-7
Related parts for 3342-7
3342-7 Summary of contents
Page 1
PE3341/2 EEPROM Programming USER’S MANUAL 6175 Nancy Ridge Drive, San Diego, CA 92121 (858) 455-0660, Fax (858) 455-0770 http://www.peregrine-semi.com ...
Page 2
... Software Installation Instructions…………………………………………………..... 11 Software Operation Instructions……………………………………………………... 11 Peregrine Semiconductor Corportation ...
Page 3
... Copyright 2002 Peregrine Semiconductor Corp. All rights reserved. Printed in the United States of America. No part of this publication may be reproduced, photocopied, stored in a retrieval system, or transmitted by electronic, mechanical or any other means without prior written permission of Peregrine Semiconductor Corp. Peregrine Semiconductor Corp., the Peregrine logotype, and UTSi are registered trademarks of Peregrine Semiconductor Corp ...
Page 4
... Peregrine Semiconductor Corportation 4 Introduction Doc. 79/0089~00A ...
Page 5
... This device complies with Part 15 of the FCC Rules. following two conditions: (1) this device may cause harmful interference, and (2) this device must accept any interference received including interference that may cause undesired operation. Peregrine Semiconductor Corportation Using the hardware and software 5 Operation is subject to the Doc ...
Page 6
... Peregrine Semiconductor Corportation 6 Hardware Section Doc. 79/0089~00A ...
Page 7
... The Programming Kit includes all of the specific software and hardware required to program the EEPROM of the PE3341/2. Included in the Programming Kit are: 1 PE3341/2 EEPROM programming Board (P/N: 101/0121~01A) 10 PE3341 or PE3342 2.7 GHz Integer-N EEPROM PLL 1 1 CD-ROM or two floppy disks with programming software included 2 Jumpers ...
Page 8
... With 2-wire power supply cable, connect the +3 V supply to J3 (J3-1 +3 and J3-3 GND) With 4-wire power supply cable, connect the +13 V supply to J6-4 (red connector), the -9 V supply to J6-1 (black connector), and the ground to J6-2 & -3 (green connector). Peregrine Semiconductor Corportation 8 Doc. 79/0089~00A ...
Page 9
... J2 Jumpered J6-4 +13V J6-3 & -2 GND F6-1 -9V Figure 1. PE3341/2 EEPROM programming board default jumper & switch settings Peregrine Semiconductor Corportation If installed J4 Jumper from All swithches of SW1 "Off" 9 center to left J3-1 +3V J3-3 GND Doc. 79/0089~00A ...
Page 10
... Peregrine Semiconductor Corportation 10 Software Section Doc. 79/0089~00A ...
Page 11
... Register” and “A Register” boxes directly. Step 7: Turn on all power supplies (+3, +12.5 and -9 V) with no part in the IC holder. Step 8: Place carefully one PE3341 the IC holder. Step 9: Click the “SEND DATA” button to send data to the PLL. Peregrine Semiconductor Corportation TM ‘95/98/2000. 11 Figure 2 shows one ...
Page 12
... Programmed Successfully!” with a green button will display in the bottom section as shown in Fig. 2. Otherwise, if any of the read back values is different from the programmed value, a message “Device Programming Failed!” with a red button will display as shown in Fig. 3. This feature can be Peregrine Semiconductor Corportation 12 Doc. 79/0089~00A ...
Page 13
... PE3341 the IC holder. If doing so, the transit created by turning power supply on or off could erase or re-program the EEPROM content. A solution is being working on. Step 13: To exit the program, click the “QUIT” button. Figure 3. Example of EEPROM Programming Software Screen when the programming is failed. Peregrine Semiconductor Corportation 13 Doc. 79/0089~00A ...