4306-0 Peregrine Semiconductor, 4306-0 Datasheet
4306-0
Specifications of 4306-0
Related parts for 4306-0
4306-0 Summary of contents
Page 1
... Product Description The PE4306 is a high linearity, 5-bit RF Digital Step Attenuator (DSA) covering attenuation range in 1dB steps, and is pin compatible with the PE430x series. This 50-ohm RF DSA provides both parallel (latched or direct mode) and serial CMOS control interface, operates on a single 3-volt supply and maintains high attenuation accuracy over frequency and temperature ...
Page 2
... Figure 6. Output Return Loss at Major 2500 3000 3500 4000 Product Specification 500 1000 1500 2000 2500 Frequency (MHz) Attenuation Steps 0 -10 -20 - -40 -50 0 500 1000 1500 2000 2500 Frequency (MHz) Document No. 70-0160-04 │ UltraCMOS™ RFIC Solutions PE4306 3000 3500 4000 3000 3500 4000 ...
Page 3
... PE4306 Product Specification Typical Performance Data @ 25°C, V Figure 7. Attenuation Error Vs. Frequency -10 0 500 1000 1500 2000 Frequency (MHz) Figure 9. Attenuation Error Vs. Attenuation Setting 1010 MHz and 1210 MHz 1.5 1 0.5 0 -0.5 1210 MHZ @ 25 C 1210 MHz @ -40 C 1210 MHz @ 1010 MHz @ 25 C ...
Page 4
... Note: Positive attenuation error indicates higher attenuation than target value ©2003-2008 Peregrine Semiconductor Corp. All rights reserved. Page 3.0 V unless otherwise noted DD Figure 12 Compression vs. Frequency 2500 3000 Product Specification 1000 1500 2000 Frequency (MHz) Document No. 70-0160-04 │ UltraCMOS™ RFIC Solutions PE4306 2500 3000 ...
Page 5
... Latch-Up Avoidance Unlike conventional CMOS devices, UltraCMOS™ de- vices are immune to latch-up blocked with an DC Switching Frequency The PE4306 has a maximum 25 kHz switching rate. DD. Resistor on Pin 1 & 3 (-VDD) to bypass and kΩ resistor on the inputs to Pin 1 & 3 (see Figure 16) will eliminate package resonance between the RF input pin and the two digital inputs ...
Page 6
... Programming Options Parallel/Serial Selection Either a parallel or serial interface can be used to control the PE4306. The P/S bit provides this selection, with P/S=LOW selecting the parallel interface and P/S=HIGH selecting the serial interface. Parallel / Direct Mode Interface The parallel interface consists of five CMOS- compatible control lines that select the desired attenuation state, as shown in Table 5 ...
Page 7
... Product Specification Evaluation Kit The Digital Attenuator Evaluation Kit board was designed to ease customer evaluation of the PE4306 DSA used in conjunction with the supplied DC cable to supply VDD, GND, and –VDD. If use of the internal negative voltage generator is desired, then connect –VDD (black banana plug) to ground external – ...
Page 8
... C, unless otherwise specified A Parameter Min LE minimum pulse width 10 LEPW Data set-up time before 10 PDSUP rising edge of LE Data hold time after 10 PDHLD falling edge of LE Document No. 70-0160-04 │ UltraCMOS™ RFIC Solutions PE4306 Product Specification ↑ LSB (last in) Max Unit ...
Page 9
... PE4306 Product Specification Figure 19. Package Drawing 0.435 0.18 DETAIL A 1. Dimension applies to metallized terminal and is measured between 0.25 and 0.30 from terminal tip. 2. Coplanarity applies to the exposed heat sink slug as well as the terminals. 3. Dimensions are in millimeters. Document No. 70-0160-04 │ www.psemi.com 4.00 2 ...
Page 10
... Figure 20. Marking Specifications Figure 21. Tape and Reel Drawing Table 10. Ordering Information Order Code Part Marking 4306-00 PE4306-EK 4306-51 4306 4306-52 4306 ©2003-2008 Peregrine Semiconductor Corp. All rights reserved. Page 4306 YYWW ZZZZZ YYWW = Date Code ZZZZZ = Last five digits of PSC Lot Number ...
Page 11
... PE4306 Product Specification Sales Offices The Americas Peregrine Semiconductor Corporation 9380 Carroll Park Drive San Diego, CA 92121 Tel: 858-731-9400 Fax: 858-731-9499 Europe Peregrine Semiconductor Europe Bâtiment Maine 13-15 rue des Quatre Vents F-92380 Garches, France Tel: +33-1-4741-9173 Fax : +33-1-4741-9173 Space and Defense Products ...