3336-1 Peregrine Semiconductor, 3336-1 Datasheet
![no-image](/images/no-image-200.jpg)
3336-1
Specifications of 3336-1
Related parts for 3336-1
3336-1 Summary of contents
Page 1
... EVALUATION KIT USER’S MANUAL Peregrine Semiconductor Corportation PE3336 6175 Nancy Ridge Drive, San Diego, CA 92121 (858) 455-0660, Fax (858) 455-0770 1 Doc. 79/0056~00A ...
Page 2
... Introduction ................................................................................................................... 4 Introduction .................................................................................................................. 5 Applications Support .................................................................................................... 5 FCC Labeling Requirement .......................................................................................... 5 Hardware Section .......................................................................................................... 6 Evaluation Kit Contents & Requirements ..................................................................... 7 Evaluation Kit Configuration ......................................................................................... 8 Evaluation Kit Setup ..................................................................................................... 9 Software Section ......................................................................................................... 13 Software Installation Instructions................................................................................ 14 Printer Port Programming........................................................................................... 14 Software Operation Instructions ................................................................................. 14 Programming Tip........................................................................................................ 15 Peregrine Semiconductor Corportation 2 http://www.peregrine-semi.com Doc. 79/0056~00A ...
Page 3
... Peregrine Semiconductor Corp. Peregrine Semiconductor Corp., the Peregrine logotype, and UTSi are registered trademarks of Peregrine Semiconductor Corp. PE3336 is a trademark of Peregrine Semiconductor Corp. Peregrine Semiconductor Corp. reserves the right to make improvements to the hardware, firmware or software described in this manual at any time and without notice ...
Page 4
... Peregrine Semiconductor Corportation 4 Introduction Doc. 79/0056~00A ...
Page 5
... Introduction This Evaluation Kit is specifically designed for evaluating the PE3336 3 GHz Integer-N PLL. The Evaluation Kit allows maximum flexibility for optimizing phase noise, spur, lock time and power performance for specific applications. Using the hardware and software provided in the Evaluation Kit both serial and direct modes of programming can be demonstrated ...
Page 6
... Peregrine Semiconductor Corportation 6 Hardware Section Doc. 79/0056~00A ...
Page 7
... Mouse Parallel Port HTML Browser to access CD contents CAUTION: The PE3336-EK circuit contains components that might be damaged by exposure to voltages in excess of the specified voltage, including voltages produced by electrostatic discharges. Handle the board in accordance with procedures for handling static-sensitive components. Avoid applying excessive voltages to the power supply terminals or signal inputs or outputs ...
Page 8
... J10 SMA connector and the jumper removed to R power-down the TCXO. The PE3336 Evaluation Kit also allows for manual programming using the fifteen on- board switches. Setting the BMODE Control switch ON (BMODE switch S3-1) enables direct mode programming. Setting the BMODE Control switch to the OFF position (S3-1) and the A3-S_mode switch to the ON position (S3-8) the serial programming mode is enabled allowing for software control ...
Page 9
... J5. Additional GND posts and test points are available on the Evaluation Board for measurement flexibility. 6. Refer to the next section for further information on configuring and running the application software. Peregrine Semiconductor Corportation The 4-wire interface cable (3-wire serial 9 Doc. 79/0056~00A ...
Page 10
... Figure 1. Typical Setup for Evaluation Kit Measurements S1 J1: 8-Wire Serial Interface to Computer Printer Port (Supplied in Kit Peregrine Semiconductor Corportation J10: External Reference Input (Do not connect if on-board TCXO is used) TCXO PLL VDD J7: 1,3 Op Amp VPOS J7: 13,15,17,19 Int-N PLL VCO VDD VCO J7: 31,33 J5: VCO Output to Spectrum Analyzer ...
Page 11
... Figure 2. Evaluation Kit Default Jumper & Switch Settings. External Reference Input S1 Switch 1 ON Enhanced Mode OFF S2 Switch 8 ON Serial Programming Enabled Peregrine Semiconductor Corportation JP1 set to utilize on-board reference J3 on-board reference supply VCO Output 11 PLL +3 V Supply J7: 1,3 Op Amp +/-6 V Supply ...
Page 12
... Figure 3. Jumper Setting to Disable On-board Reference. External Reference Input Peregrine Semiconductor Corportation JP1 set to utilize external reference (left two pins shorted) J3 jumper removed 12 Doc. 79/0056~00A ...
Page 13
... Peregrine Semiconductor Corportation 13 Software Section Doc. 79/0056~00A ...
Page 14
... J1-5 pin of the Serial Control connector and programming both primary and secondary registers. Software Operation Instructions To run the PE3336 using your computer’s parallel port follow steps 1 through 7 below and reference Figure 4. Step 1: Start the Peregrine Integer-N PLL EK Control program. This is a generic program for all Interger-N PLL’ ...
Page 15
... Step 2: Select the PE3336 from the pull-down menu button in the upper left corner of the program screen. This selection will enable certain product specific modes of operation. Step 3: If the on-board reference is being used, set the reference frequency to 10 MHz by typing 10 into the reference frequency box external reference is applied, type in the appropriate reference value in MHz ...
Page 16
... Figure 4. PE3336 Software Control Panel Pulldown product menu ! Light blue number boxes identify user defined program states and can be modified by utilizing the arrows next to the boxes or clicking into the box and typing the appropriate value. Either clicking on the light blue switches or typing the counter variable into the text box can program the registers ...