ZPM3570-C RFM, ZPM3570-C Datasheet - Page 17

• Manufacturer Part Number: ZPM3570-C
• Description: TXRX ZIGBEE PRO 2.4GHZ ISM
• Manufacturer: RFM
• Series: ZPMr

Specifications of ZPM3570-C

• Frequency: 2.4GHz ~ 2.5GHz
• Data Rate - Maximum: 250kbps
• Modulation Or Protocol: 802.15.4 Zigbee
• Applications: General Purpose
• Power - Output: 20dBm
• Sensitivity: -103dBm
• Voltage - Supply: 2.4 V ~ 3.4 V
• Current - Receiving: 35mA
• Current - Transmitting: 175mA
• Data Interface: PCB, Surface Mount
• Memory Size: 8Mb
• Antenna Connector: On-Board, Chip
• Operating Temperature: -40°C ~ 85°C
• Package / Case: Module
• Wireless Frequency: 2.4 GHz
• Interface Type: I2C, SPI, UART
• Modulation: DSSS
• Security: 128 bit AES
• Operating Voltage: 2.4 V to 3.4 V
• Output Power: 20 dBm
• Operating Temperature Range: - 40 C to + 85 C
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 583-1161; ZPM3570

installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the interfer-
ence by one or more of the following measures: reorient or relocate the receiving antenna, increase the
separation between the equipment and receiver, connect the equipment into an outlet on a circuit differ-
ent from that to which the receiver is connected, or consult the dealer or an experienced radio/TV techni-
cian for help.
11.1.1 FCC Labeling Requirements
When integrating the ZPM3750 into a product the FCC labeling requirements must be met. This includes
a clearly visible label on the outside of the finished product specifying the ZPM3750 FCC identifier (FCC
ID: QPU3020) as well as the notice above. The exterior label can use wording such as “Contains Trans-
mitter Module FCC ID: QPU3020” or “Contains FCC ID: QPU3020” although any similar wording that ex-
presses the same meaning may be used.
11.1.2 RF Exposure
This module has been certified for remote and base radio applications and is not intended to be operated
within 20 cm of the body. If the module will be used for portable applications, the device must undergo
SAR testing.
The following statement must be included as a CAUTION statement in manuals for the products to alert
users on FCC RF exposure compliance:
“WARNING: To satisfy FCC RF exposure requirements for mobile transmitting devices, a separation dis-
tance of 20 cm or more should be maintained between the antenna of this device and persons during op-
eration. To ensure compliance, operations at closer distances than this are not recommended.”
11.2 IC Notice (Canada)
The term “IC” before the certification/registration number only signifies that the Industry Canada technical
specifications were met.
Le terme “IC” devant le numéro de certification /d’enregistrement signifie seulement que les spécifications
techniques Industrie Canada ont été respectées.
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to The
following two conditions: (1) this device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation of the device.
Cet appareil est conforme avec Industrie Canada RSS standard exempts de licence (s). Son utilisation
est soumise à Les deux conditions suivantes: (1) cet appareil ne peut pas provoquer d'interférences et (2)
cet appareil doit accepter Toute interférence, y compris les interférences qui
peuvent causer un mauvais fonctionnement du dispositif.
This device complies with Health Canada’s Safety Code 6 / IC RSS-210. The installer of this device
should ensure that RF radiation is not emitted in excess of the Health Canada’s requirement. Information
can be obtained at: http://www.hc-sc.gc.ca/ewh-semt/pubs/radiation/radio_guidelignes_direct-eng.php
www.RFM.com
Technical support +1.678.684.2000
Page 17 of 18
© 2011 by RF Monolithics, Inc.
E-mail:
[e-mail]
ZPM3570 Data Sheet - 05/25/11