STG5223QTR STMicroelectronics, STG5223QTR Datasheet
![IC SWITCH DUAL SPDT 10QFN](/photos/6/87/68704/497-10-qfn_series_sml.jpg)
STG5223QTR
Specifications of STG5223QTR
STG5223QTR
Available stocks
Related parts for STG5223QTR
STG5223QTR Summary of contents
Page 1
... The switches nS1 are ON (connected to common ports Dn) when the nIN input is held high and OFF (high impedance state Table 1. Device summary Order code STG5223QTR May 2009 Low voltage 0.5 Ω dual SPDT switch = 25 ° ° °C) at exists between the two ports) when nIN is held low ...
Page 2
Contents Contents 1 Pin settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...
Page 3
STG5223 1 Pin settings 1.1 Pin connection Figure 1. Pin connection (top through view) 1.2 Pin description Table 2. Pin description Pin number Warning SEL2 8 1 ...
Page 4
Input equivalent circuit and truth table 2 Input equivalent circuit and truth table Figure 2. Input equivalent circuit Table 3. Truth table High impedance 4/19 Switch S1 ON (1) OFF Doc ID 14312 Rev 3 STG5223 ...
Page 5
STG5223 3 Maximum rating Stressing the device above the rating listed in the “Absolute maximum ratings” table may cause permanent damage to the device. These are stress ratings only and operation of the device at these or any other conditions ...
Page 6
Maximum rating 3.1 Recommended operating conditions Table 5. Recommended operating conditions Symbol V Supply voltage CC V Input voltage I V Control input voltage IC V Output voltage O T Operating temperature op dt/dv Input rise and fall time control ...
Page 7
STG5223 4 Electrical characteristics Table 6. DC specifications Symbol Parameter High level input V IH voltage Low level input V IL voltage Switch resistance ON resistance ΔR match between ON (1) channels ON resistance R FLAT (2) ...
Page 8
Electrical characteristics Table 6. DC specifications (continued) Symbol Parameter Quiescent supply I current low CCLV voltage driving 1. Δ ON(max) ON(min) 2. Flatness is defined as the difference between the maximum and minimum value ...
Page 9
STG5223 Table 8. Analog switch characteristics (C Symbol Parameter OIRR Off isolation Xtalk Crosstalk Total harmonic THD distortion -3dB bandwidth 1.65 − −4 Control pin C input IN capacitance Sn port capacitance C ON when switch is enabled ...
Page 10
Test circuit 5 Test circuit Figure 3. ON resistance Figure 4. OFF leakage V SS 10/ GND GND S(OFF GND Doc ID 14312 ...
Page 11
STG5223 Figure 5. OFF isolation V S Figure 6. Bandwidth GND GND GND Doc ID 14312 Rev 3 Test circuit V OUT 50 Ω CS00381 D V OUT ...
Page 12
Test circuit Figure 7. Channel-to-channel crosstalk Figure 8. Test circuit 5/ equivalent (includes jig and probe capacitance Ω or equivalent pulse generator (typically 50 Ω ...
Page 13
STG5223 Figure 9. Break-before-make time delay Figure 10. Charge injection (V Figure 11. Turn on, turn off delay time GEN GEN OUT GND Doc ...
Page 14
Package mechanical data 6 Package mechanical data In order to meet environmental requirements, ST offers these devices in different grades of ® ECOPACK packages, depending on their level of environmental compliance. ECOPACK specifications, grade definitions and product status are available ...
Page 15
STG5223 Table 9. Mechanical data for QFN10 (1.8 x 1.4 x 0.5 mm) - 0.40 mm pitch Symbol Figure 13. Recommended footprint for QFN10 (1.8 x 1.4 x 0.5 mm) - ...
Page 16
Package mechanical data Figure 14. Carrier tape for QFN10 (1.8 x 1.4 x 0.5 mm) Figure 15. Reel information (back view) for QFN10 (1.8 x 1.4 x 0.5 mm) 16/19 Doc ID 14312 Rev 3 STG5223 ...
Page 17
STG5223 Figure 16. Reel information (front side) for QFN10 (1.8 x 1.4 x 0.5 mm) Doc ID 14312 Rev 3 Package mechanical data 17/19 ...
Page 18
Revision history 7 Revision history Table 10. Document revision history Date 06-Dec-2007 10-Jul-2008 18-May-2009 18/19 Revision 1 Initial release. Updated R and Modified: Table 6 and ECOPACK text. 3 Content reworked to improve readability in Doc ID ...
Page 19
... STG5223 Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale. ...