CAT24M01WI-GT3 ON Semiconductor, CAT24M01WI-GT3 Datasheet
CAT24M01WI-GT3
Specifications of CAT24M01WI-GT3
Available stocks
Related parts for CAT24M01WI-GT3
CAT24M01WI-GT3 Summary of contents
Page 1
CAT24M01 CMOS Serial EEPROM Description The CAT24M01 is a 1024 kb Serial CMOS EEPROM, internally organized as 131,072 words of 8 bits each. It features a 256−byte page write buffer and supports the Standard (100 ...
Page 2
AYMXXX (SOIC−8) 24M01A = Specific Device Code A = Assembly Location Y = Production Year (Last Digit Production Month (1− XXX = Last Three Digits of XXX = Assembly Lot Number Table 1. ABSOLUTE ...
Page 3
Table 4. PIN IMPEDANCE CHARACTERISTICS −40°C to +85°C and Symbol C (Note 4) SDA I/O Pin Capacitance IN C (Note 4) Input Capacitance (other pins ...
Page 4
Power-On Reset (POR) The CAT24M01 incorporates Power−On Reset (POR) circuitry which protects the internal logic against powering up in the wrong state. The device will power up into Standby mode after V exceeds the POR trigger level and will power ...
Page 5
SCL SDA START CONDITION BUS RELEASE DELAY (TRANSMITTER) SCL FROM 1 MASTER DATA OUTPUT FROM TRANSMITTER DATA OUTPUT FROM RECEIVER START LOW SCL t SU:STA t HD:STA SDA IN SDA OUT Figure 2. Start/Stop Timing 1 0 ...
Page 6
WRITE OPERATIONS Byte Write In Byte Write mode the Master sends a START, followed by Slave address, two byte address and data to be written (Figure 6). The Slave acknowledges all 4 bytes, and the Master then follows up with ...
Page 7
BUS ACTIVITY: SLAVE R MASTER ADDRESS T SDA LINE S SCL SDA 8th Bit Byte n S BUS T ACTIVITY: A SLAVE MASTER R ADDRESS a − SDA LINE ADDRESS ...
Page 8
READ OPERATIONS Immediate Address Read In standby mode, the CAT24M01 internal address counter points to the data byte immediately following the last byte accessed by a previous operation. If that ‘previous’ byte was the last byte in memory, then the ...
Page 9
PIN # 1 IDENTIFICATION D TOP VIEW SIDE VIEW Notes: (1) All dimensions are in millimeters. (2) Complies with JEDEC MS-001. PACKAGE DIMENSIONS PDIP−8, 300 mils CASE 646AA−01 ISSUE A SYMBOL ...
Page 10
PIN # 1 IDENTIFICATION TOP VIEW SIDE VIEW Notes: (1) All dimensions are in millimeters. Angles in degrees. (2) Complies with JEDEC MS-012. PACKAGE DIMENSIONS SOIC 8, 150 mils CASE 751BD−01 ISSUE O SYMBOL ...
Page 11
E1 e TOP VIEW SIDE VIEW Notes: (1) All dimensions are in millimeters. Angles in degrees. (2) Complies with JEDEC MO-153. PACKAGE DIMENSIONS TSSOP8, 4.4x3 CASE 948AL−01 ISSUE O SYMBOL MIN A A1 0.05 A2 ...
Page 12
PIN#1 IDENTIFICATION TOP VIEW SIDE VIEW Notes: (1) All dimensions are in millimeters. Angles in degrees. (2) Complies with EIAJ EDR-7320. PACKAGE DIMENSIONS SOIC−8, 208 mils CASE 751BE−01 ISSUE O SYMBOL ...
Page 13
Í Í Í E PIN 1 REFERENCE Í Í Í Í Í Í 0.15 C Í Í Í 0.15 C TOP VIEW DETAIL NOTE 4 C SIDE VIEW 0.10 C ...
Page 14
... The standard lead finish is NiPdAu. 11. The device used in the above example is a CAT24M01WI−GT3 (SOIC−JEDEC, Industrial Temperature, NiPdAu, Tape & Reel, 3,000/Reel). 12. For SOIC, EIAJ (X) package the standard lead finish is Matte−Tin. This package is available in 2,000 pcs/reel, i.e., CAT24M01XI−T2. ...