MAX394CWP+ Maxim Integrated Products, MAX394CWP+ Datasheet - Page 6

• Manufacturer Part Number: MAX394CWP+
• Description: IC SWITCH QUAD SPDT 20SOIC
• Manufacturer: Maxim Integrated Products

Specifications of MAX394CWP+

• Function: Switch
• Circuit: 4 x SPDT
• On-state Resistance: 35 Ohm
• Voltage Supply Source: Single, Dual Supply
• Voltage - Supply, Single/dual (±): 2.7 V ~ 15 V, ±2.7 V ~ 8 V
• Current - Supply: 1µA
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 20-SOIC (0.300", 7.50mm Width)
• Number Of Switches: Quad
• Switch Configuration: SPDT
• On Resistance (max): 35 Ohms
• On Time (max): 130 ns
• Off Time (max): 75 ns
• Off Isolation (typ): 66 dB
• Supply Voltage (max): +/- 8 V
• Supply Voltage (min): +/- 2.7 V
• Supply Current: 0.06 uA
• Maximum Power Dissipation: 696 mW
• Maximum Operating Temperature: + 70 C
• Mounting Style: SMD/SMT
• Description/function: Analog Switch
• Input Level: CMOS, TTL
• Minimum Operating Temperature: 0 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Low-Voltage, Quad, SPDT,
CMOS Analog Switch
ELECTRICAL CHARACTERISTICS—Single +3.3V Supply (continued)
(V+ = 3.0V to 3.6V, GND = 0V, V
Note 2:
this data sheet.
Note 3:
Note 4:
Note 5:
Note 6:
Note 7:
Note 8:
6
Input Current with Input
Voltage High
Input Current with Input
Voltage Low
DIGITAL LOGIC INPUT
DYNAMIC
Turn-On Time (Note 3)
Turn-Off Time (Note 3)
Break-Before-Make Delay
(Note 3)
Charge Injection (Note 3)
SUPPLY
Power-Supply Range
Positive Supply Current
Negative Supply Current
_______________________________________________________________________________________
PARAMETER
The algebraic convention, where the most negative value is a minimum and the most positive value a maximum, is used in
Guaranteed by design.
ΔR
specified voltages. Flatness is defined as the difference between the maximum and minimum value of on-resistance as
measured over the specified analog signal range.
Leakage parameters are 100% tested at maximum rated hot temperature and guaranteed by correlation at room temperature.
See Figure 6. Off-isolation = 20log
Between any two switches. See Figure 3.
Leakage testing at single supply is guaranteed by testing with dual supplies.
ON
= ΔR
ON
(max) - ΔR
SYMBOL
INH
V
t
I
I
t
ON
OFF
INH
V+
INL
ON
CTE
t
I+
= 2.4V, V
I-
D
(min). On-resistance match between channels and flatness are guaranteed only with
V
V
V
V
Figure 5
C
R
All channels on or off, V
V+ = 3.6V, V- = 0V
All channels on or off, V
V+ = 3.6V, V- = 0V
10
INL
IN
IN
COM
COM
GEN
L
= 1.0nF, V
V
= 2.4V, all others = 0.8V
= 0.8V, all others = 2.4V
COM
= 0.8V, T
= 0Ω, Figure 6
= 1.5V, Figure 2
= 1.5V, Figure 2
/V
NC
GEN
A
or V
= T
CONDITIONS
= 0V,
NO
MIN
, V
to T
IN
IN
COM
T
T
T
T
= 0V or V+,
= 0V or V+,
MAX
A
A
A
A
= +25°C
= +25°C
= +25°C
= +25°C
= output, V
, unless otherwise noted.)
NC
or
NO
= input to off switch.
MIN
-1.0
-1.0
-1.0
-1.0
2.7
5
(Note 2)
+0.005
+0.005
+0.01
-0.01
TYP
20
1
MAX
+1.0
+1.0
+1.0
+1.0
400
150
16
5
UNITS
µA
µA
pC
µA
µA
ns
ns
ns
V